background image

 

 

3

 

                                                         
 
 

IMPORTANT SAFETY INSTRUCTIONS 

 

1.  Read these instructions - All the safety and operating instructions should be read before the 

appliance is operated 

 2.  Keep these instructions - The safety and operating instructions should be kept for future 

reference. 

  3.  Heed all warnings - All warnings on the appliance and in the operating instructions should 

be adhered to. 

  4.  Follow all instructions - All operation and use instructions should be followed. 
 5.  Do not use this apparatus near water - The appliance should not be used near water; for 

example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a 
swimming pool, and the like. 

  6.  Clean only with dry cloth - The appliance should be cleaned only as recommended by the 

manufacturer. 

7.  Do not block any ventilation openings. Install in accordance with the manufacturer’s 

instructions. - The appliance should be situated so that its location or position does not 
interfere with its proper ventilation. For example, the appliance should not be situated on a 
bed, sofa, rug, or similar surface that may block the ventilation openings; or placed in a 
built-in installation, such as a bookcase or cabinet that may impede the flow of air through 
the ventilation openings. 

8.  Do not install near any heat sources such as radiators, heat registers, stoves or other 

apparatus (including amplifiers) that produce heat. 

9.      Protect the power cord from being walked on or pinched particularly at plugs, convenience 

receptacles,      and the point where they exit from the apparatus. 

10.  Only use attachments / accessories specified by the manufacturer   
11.      Use only with the cart, stand, tripod, bracket, or table specified by the 

        manufacturer, or sold with the apparatus. When a cart is used,   

use caution when moving the cart/apparatus combination to avoid injury 

 from tip-over. 

 
12.    Unplug this apparatus during lightning storms or when unused for a                 

long periods of time. 

13.      Power Sources - The appliance should be connected to a power supply 

only of the type described in the operating instructions or as marked on the appliance. Do 
not overload wall outlet. 

14.  Wall and Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as 

recommended by the manufacturer. 

15.  Power Lines - An outdoor antenna should be located away from power lines. 
16.  Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not 

spilled into the enclosure through openings. 

17.  Refer all servicing to qualified service personnel. Servicing is required when the apparatus 

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has 
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to 
rain or moisture, does not operate normally, or has been dropped.     

18.  Servicing - The user should not attempt to service the appliance beyond that described in 

the operating instructions. All other servicing should be referred to qualified service 
personnel. 

                                                                                                                     

 
 
 
 

Summary of Contents for NSM-436


















Reviews: