background image

2.2. Device front panel

At the

front panel

of the device can be found the following information

VIN

Input for the

power supply

. The device must be connected to a

5 – 30VDC

(*) power line. It is

recommended to use a stable power line.

VOUT

Output voltage from the input one. By means of this connector, it is possible to feed another device with
the same voltage as connected to VIN. It is highly recommended to feed an Advertisim device.

PC – MicroUSB

Programming input of the device if connected to a PC. It can also be used as an input power supply,
when not using the VIN connector.

Discover Button

This button is configured to complete two actions:

Nayar Switch’s identification on app

: A single press on this button helps identify in the app the

device among all the other available products.

Link to Wi-Fi network created by Nayar Switch

: A single press on this button allows a different

Nayar Systems’ product to link to the Wi-Fi network created by the Nayar Switch.

A touch on the

Discover

button causes the Discover LED of Nayar Switch to light up.

For product versions v5.0 and older, the operating range is

5 – 16 VDC

.

*

Nayar Systems

Switch - 1_en

Page 5 of 19

Summary of Contents for Switch






















Reviews: