background image

 

BWG-S

ERIES

 

O

PERATION 

& M

AINTENANCE 

M

ANUAL

 

 

12838 Stainless Drive, Holland, MI 49424 

 

Phone: 616/399-5600 Fax 616/399-3084 

 

 

Copyright 2018 BRAWN Mixer 

www.BRAWNMIXER.com 

Page 11 of 11

 

11/27/

2018 

 

 

WARRANTY 

 
WARRANTY

:  All equipment or parts covered by this 

manual are guaranteed free from defective material and 
workmanship for a period of twelve (12) months from 
date of shipment, under normal use and service. This 
warranty does not cover failure of normal wear parts 
unless the failure of such part has resulted from 
defective material and workmanship. BRAWN Mixer will 
repair or replace, at its option, any equipment which has 
been found to be defective and is within the warranty 
period, provided that the equipment is shipped, with 
previous factory authorization, freight prepaid, to 
BRAWN's plant in Holland, Michigan, USA.  All return 
shipments are made FOB BRAWN's factory. BRAWN is 
not responsible for removal, installation, or any other 
incidental expenses incurred in shipping the equipment 
to or from BRAWN.  In the case of components 
purchased by BRAWN Mixer and incorporated in the 
equipment, the component manufacturer's guarantee 
shall apply. NOTE:  Any modifications or corrective work 
done to the equipment which were not specifically 
authorized in writing by BRAWN Mixer shall void this 
limited warranty, and BRAWN Mixer shall accept no 
liability for any of the corrective work or expenditures 
which were conducted without their prior, written 
authorization. BRAWN Mixer shall not be held liable for 
any further cost, expense, or labor to replace equipment 
or replaceable parts, or indirect or consequential 
damages. 
 

With the exceptions of the limited warranty set out 
above, there are no other understandings, agreements, 
representatives, or warranties implied (including any 
regarding the merchant-ability or fitness for a particular 
purpose), not specified herein, respecting this agreement 
or equipment, hereunder. This contract states the entire 
obligation of BRAWN Mixer in connection with this 
transaction. 

 

SHOULD WE MAKE A MISTAKE... 

 

BRAWN Mixer's  

Direct Returns Policy 

 
To ensure proper handling of your return, please take a 
moment to read the following: 

 

 

ALL

 returns require a 

RETURN GOODS 

AUTHORIZATION (RGA) NUMBER

. We are unable 

to process your return or issue proper credit without 
an approved 

RGA

 number. 

 

 

ALL

 returns must be 

COMPLETE

, including all 

original warranties, manuals, documentation and 
packaging. 

 

 

ALL

 product must be received within 14 days of 

issuing an 

RGA

 number. 

 
 

How to Return Product

 

 

You must have a 

RETURN GOODS AUTHORIZATION 

(RGA)

 number before you return any product to BRAWN 

Mixer. To obtain this number, call 

616/399-5600

 and ask 

for Customer Service. Be sure to have available the 
following information: 
 

  your order number 

  the BRAWN product serial number 

  the part number and description of the product 

  the reason for the return 

 

 

   

I M P O R T A N T

   

 

 
The Return Goods Authorization number must be written 
clearly on all boxes being returned.  C.O.D. shipments 
will not be accepted.

 

Summary of Contents for BRAWN MIXER BWG Series





















Reviews: