background image

Model 7815 Parcel Bench Scale User’s Manual

8

After the NCI Model 7815 is properly installed
and power is applied, the display will perform a
countdown test to insure all display segments are
functional.

After this test is completed, the display should
show zero (0.0).

If the display indicates a slightly “off” zero condi-
tion (either a number in the display or dashes at
the bottom of the display), press the 

ZERO 

key.

When the display shows 

0.0

, it is ready to weigh.

Place item or parcel on the weigh platter and the
weight will be displayed. This information can be
transmitted when requested by the computer.

Model 7815 scales can have an optional remote
display (shown above). The remote display has a
keyboard and can be used in place of the resi-
dent display. To activate the remote display,
power down the scale, plug the remote display
cable end into the marked socket on the back of
the unit. Reapply power and weight data will
appear on both the resident and remote displays.
The control keys (i.e., 

ZERO 

and 

TEST

) are

active on both displays in the Model 7815.

Operation

Operating Instructions

NCI Model 7815

Resident Display

Remote Displays

Summary of Contents for 7815

























Reviews: