background image

11

9. Key Features

7PCS 15W 4-IN-1 LEDs (R,G,B,W )
60,000 hours life span for LEDs and low power consumption
Intelligent temperature sensor for LEDs(over heat protection)
High efficiency 8 degree optic lens
Color range with 16.7 millions additive RGBW colors
High light output as 860LUX@ 7M at full
0-100% smooth linear dimmer with flicker free
20t/s strobe effect with variable speed
Pre-programmed random strobe and pulse effects
11/15CH DMX channels
Built-in programs with macro effects
DMX512, master-slave and sound activated controllable or auto operation
High definition blue TFT LCD display
Quiet, smooth and fast PAN/TILT movement
Low noise and efficient FAN cooling system
540° PAN and 250° TILT movement
Scan position memory, auto reposition after unexpected movement
Compact size with only 4.9KG body and 310mm in height
IEC power connector
45

max ambient temperature

IP20 protection rating
3-Pin XLR DMX input/output

10. Specifications

Input Voltage: AC90-260V 50/60Hz
LED Quantities: 7 PCS of 15W 4-IN-1 LEDs (R, G, B, W)
Control Signal: DMX512, master-slave and sound activated or auto operation
Control Channel:11/ 15 DMX channels
Power Consumption: 120W
Dimensions: 152(L)*265(W)*310(H)mm
Packing Dimensions:260(L)*320(W)*335(H)mm
Net Weight: 5.5kg
Gross Weight: 7.5kg

11

Summary of Contents for 7*15W 4in1















Reviews: