NEC ELECTRA ELITE IPK II Programming Manual Download

Page: 371 / 617

Document Revision 1

Electra Elite IPK II

2 - 336

Program 34 : Tie Line Setup

Conditions

None

Feature Cross Reference

T1 Trunking (with ANI/DNIS Compatibility)

Tie Lines

Routing When Destination Busy or No
Answer

This option lets you determine how the system
will handle an ANI/DNIS call if destination is
busy or does not answer.

= Play Busy or

Ringback Tone to
Caller (Busy/
NoAns)

= Route Caller to

Ring Group
Specified in
Program 25-04
(Transfer)

25-04

Calling Number Address Length

When Item 1=0 (ANI/DNIS receive format is
address), use this option to specify the
address length. The choices are from 1 to 8
digits in length.

1~8

34-09-01

Item

No.

Name

Input Data

Default

Related

Program

COS 01~14

COS 15

Summary of Contents for ELECTRA ELITE IPK II










































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ELECTRA ELITE IPK II

Reviews:

Related manuals for ELECTRA ELITE IPK II

Brands by name

Popular brands

NEC ELECTRA ELITE IPK II, Programming Manual

Search results

Summary of Contents for ELECTRA ELITE IPK II

Reviews:

Related manuals for ELECTRA ELITE IPK II

Brands by name

Popular brands