NEC ELECTRA ELITE IPK II Programming Manual Download | Manualshive

Page: 491 / 617

background image

Document Revision 1

Electra Elite IPK II

2 - 456

Program 47 : In-Mail

J

GOTO Action - Go to Mailbox (7) (GOTO)

Use this option to provide Automated Attendant callers with the ability to route to
Call Routing and Announcement Mailboxes. For example, a caller can dial a
digit for Sales, and then go to the Call Routing or Announcement Mailbox that
provides the dialing options and instructions for Sales.

Number Option

To have Automated Attendant callers dial a single digit to go to a Call Routing or
Announcement Mailbox, enter the mailbox number in the corresponding
Number option.

For example, to have key 1 go to Call Routing Mailbox 01, for key 1 enter
GOTO for the Action and 01 for the corresponding Number.

To have IPK II In-Mail require Automated Attendant callers to enter a Call
Routing or Announcement Mailbox to go to, enter XXX in the corresponding
Number option. The key you choose must represent the first digit in the mailbox
numbers.

For example, to allow callers to go to mailboxes 000-015, for key 0 enter
GOTO for the Action and XXX for the corresponding Number.

To log into any valid Call Routing or Subscriber Mailbox, enter IXXX in the
corresponding Number option.

For example, to allow callers to dial 1 plus any Call Routing or
Announcement Mailbox number to go to, for key 1 enter GOTO for the
Action and IXXX for the corresponding Number.

J

UND Action - Undefined Routing (0) (UND)

Use this key action if you want a key to have no routing (no operation). When an
Automated Attendant caller presses an undefined key, they hear, “That is an
invalid entry.” The caller can then dial another option.

«
...
489
490
491
492
493
...
»

Summary of Contents for ELECTRA ELITE IPK II










































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ELECTRA ELITE IPK II

Brand: National Instruments Pages: 11

Brand: Danfoss Pages: 61

Brand: LORD Pages: 9

ILDA Gem Laser projector tool

Brand: Stanwax Laser Pages: 3

Armor 101 Series

Brand: Lochinvar Pages: 28

Armor 101 Series

Brand: Lochinvar Pages: 44

Brand: 3Com Pages: 18

Brand: Supermicro Pages: 24

Brand: CAP-XX Pages: 8

Brand: Zoom Pages: 48

HiGain H2TU-R-402 List 7A

Brand: ADC Pages: 7

Brand: Renesas Pages: 28

RanaSystems 13-0010--001

Brand: RANA Systems Pages: 328

Brand: SYNTEK Pages: 41

IPS Pro-Module-24C-GE-BP-TM

Brand: Trend Micro Pages: 3

Brand: MA lighting Pages: 49

EK-FC750 GTX Series

Brand: ekwb Pages: 2

Brand: IEI Technology Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands