manualshive.com logo in svg

NEC EXP704, Maintenance Manual

The NEC EXP704 Maintenance Manual is a comprehensive guide that allows users to seamlessly maintain and troubleshoot their NEC EXP704 device. This essential manual can be conveniently downloaded for free from our website, ensuring access to valuable information at your fingertips.

Share
Download
background image

1. POST Error Message 

 

Express5800/E120g-M  Maintenance Guide 

172

Chapter 3  Appendix 

Error Message 

Cause 

Action 

C10E 

BMC SDR Repository empty.  

An error was detected on BMC SDR. 

Unplug the power cord, wait for at least 30 
seconds, and then restart the server. 

 

 

C10F 

IPMB signal lines do not 

respond.  

Failure of Satellite Management 
Controller was detected. 

C110 

BMC FRU device failure.  

An error was detected in FRU that 
contains device information. 

C111 BMC 

SDR Repository failure. 

Failure was detected in SROM that 
stores the SDR. 

C112 

BMC SEL device failure.  

Device failure was detected in BMC 
SEL. 

C113 

BMC RAM test error.  

An error was detected in BMC RAM. 

C114 

BMC Fatal hardware error.  

A hardware error was detected in 
BMC. 

C115 Management 

controller 

not responding 

Management controller does not 
respond. 

Update the BMC firmware.   

C116 

Private I2C bus not 

responding. 

Private I2C bus does not respond. 

Turn off the power and unplug the power 
cord, wait for at least 30 seconds, and then 
restart the server.   

C117 

BMC internal exception 

BMC internal error was detected. 

C118 

BMC A/D timeout error. 

BMC A/D timeout error was detected. 

C119 

SDR repository corrupt. 

BMC error or illegal SDR data was 
detected. 

C11A SEL 

corrupt. 

BMC error or illegal system event log 
data was detected. 

C11B 

BMC Mezzanine card is not 

found. 

BMC Mezzanine card is not installed. 

Contact your sales representative. 

C11C 

BMC Mezzanine partition is 

invalid. 

A format error was detected in BMC 
Mezzanine card. 

C11D 

BMC is in Forced Boot Mode. 

Detected that BMC is in Forced Boot 
Mode. 

Turn off the power, unplug the power cord, 
and check the jumper switch setting on 
motherboard. Wait for at least 30 seconds, 
and then restart the server.   

C11E 

Communication with BMC was 

failed in previous boot 

 

Communication with BMC was failed 
in previous boot 

Turn off the power and unplug the power 
cord, wait for 30 seconds, and then reboot 
the server.   

C11F 

Backup Data of BMC Mezzanine 

card has corrupted. 

Inconsistency was found on BMC 
mezzanine card. 

Contact your sales representative. 

 

C200 

The error occurred during 
memory configuration check. 

Memory configuration could not be 
obtained. 

C201 Memory 

Configuration change is 

detected. 

The memory configuration has 
changed since the previous startup. 

When 

Check previous system Config

 is 

enabled in 

Server

 menu of the setup, this 

message appears if the configuration was 
changed since the previous startup. If this 
message appears even when no 
configuration change has been made, 
contact your service representative.   

C202 

The error occurred during CPU 
configuration check. 

The CPU information could not be 
obtained. 

Contact your service representative. 

C203 

CPU Configuration change is 
detected. 

The CPU configuration has changed 
since the previous startup. 

When 

Check previous system Config

 is 

enabled in 

Server

 menu of the setup, this 

message appears if the configuration was 
changed since the previous startup. If this 
message appears even when no 
configuration change has been made, 
contact your service representative. 

C300 Out-of-band 

setup 

configuration failure 

Configuration change requested by 
remote terminal via network failed. 

Turn off the power and unplug the power 
cord, wait for at least 30 seconds, then 
restart the server.   

C301 

SDR mismatch error 

Inconsistency in the hardware 
information of the sensor data record 
was detected 

Contact your sales representative. 

C302 

Hardware configuration 

error. 

Illegal hardware configuration was 
detected. 

C303 

FAN Structure ID command 

error. 

Illegal fan control was detected when 
RAID Controller is installed. 

Summary of Contents for EXP704







































































































































































































Reviews:

No comments

Related manuals for EXP704

Canon ColorPASS-Z5000 Getting Started preview
ColorPASS-Z5000
Brand: Canon Pages: 130
TANDBERG S3 Administrator'S Manual preview
S3
Brand: TANDBERG Pages: 127
Yamaha MCX-2000 - MusicCAST Digital Audio Server Owner'S Manual Addendum preview
MCX-2000 - MusicCAST Digital Audio Server
Brand: Yamaha Pages: 25
IBM P 615 series Service Manual preview
P 615 series
Brand: IBM Pages: 491
Sun Microsystems iPlanet Web Server Installation Manual preview
iPlanet Web Server
Brand: Sun Microsystems Pages: 62
Supero SUPERSERVER 1018D-73MTF User Manual preview
SUPERSERVER 1018D-73MTF
Brand: Supero Pages: 124
ORing Industrial Networking Corp. IDS-181A Quick Installation Manual preview
IDS-181A
Brand: ORing Industrial Networking Corp. Pages: 2
Black Box Terminal Server User Manual preview
Terminal Server
Brand: Black Box Pages: 131
Kystar Kommander F2 Instruction preview
Kommander F2
Brand: Kystar Pages: 81
Star Lake SCH200 User Manual preview
SCH200
Brand: Star Lake Pages: 76
Neat D-SERVER Technical Handbook preview
D-SERVER
Brand: Neat Pages: 124
Planet Networking & Communication ICS-2200T User Manual preview
ICS-2200T
Brand: Planet Networking & Communication Pages: 67
Planet Networking & Communication ICS-2100T User Manual preview
ICS-2100T
Brand: Planet Networking & Communication Pages: 76
Z Microsystems ZX2 User Manual preview
ZX2
Brand: Z Microsystems Pages: 21
CTC Union DVS-8301 User Manual preview
DVS-8301
Brand: CTC Union Pages: 53
GIGA-BYTE TECHNOLOGY E162-220 User Manual preview
E162-220
Brand: GIGA-BYTE TECHNOLOGY Pages: 107
Iomega 1562 Installation Manual preview
1562
Brand: Iomega Pages: 23
IPX VE-3500 Installation & Operation Manual preview
VE-3500
Brand: IPX Pages: 94

Brands by name

Popular brands

Load more brands