NEC Express5800/120Rh-2 User Manual Download | Manualshive

Page: 132 / 406

background image

4-36 Configuring Your Server

Creating RAID1 Array

To create a RAID1 array, perform either of the followings:

Create a new RAID1 array.

Migrate to RAID1 array using the data stored in an existing single disk. (Migration)

Creating RAID1 array using the existing single hard disk drive is called "migration". In migration,
the source hard disk drive must have been used as the boot disk in the standard SCSI connection.

Refer to "HostRAID Setup Card" for details of migration.

To create a RAID1 array:

1.

Select [RAID-1] on the [Select RAID Type] window.

2.

Use the cursor key to move the focus to the desired hard disk drive and determine it by

Space

, and then press

Enter.

A [X] mark is placed next to the selected hard disk drive.

Select one of the options in [RAID-1 Build Option] window and press

Enter

.

Available options are as follows:

–

Create new RAID-1:

Default

–

Copy from (X) to (Y):

Copy data from the disk of ID X to that of ID Y.

–

Copy from (Y) to (X):

Copy data from the disk of ID Y to that of ID X.

«
...
130
131
132
133
134
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

ShareCenter Pro DNS-1200-05

Brand: D-Link Pages: 68

Brand: IBM Pages: 142

Brand: Kontron Pages: 110

Cyclades-PR4000

Brand: Cyclades Pages: 174

Brand: Belkin Pages: 2

Brand: Crestron Pages: 2

Brand: Olive Pages: 103

Brand: IOGear Pages: 48

Active Fabric Manager

Brand: Dell Pages: 44

Brand: Dell Pages: 120

Brand: Dell Pages: 76

Active Fabric Manager

Brand: Dell Pages: 127

Brand: Dell Pages: 122

DR4000 Restore Manager

Brand: Dell Pages: 156

Chassis Management Controller

Brand: Dell Pages: 234

Brand: Dell Pages: 160

Brand: Dell Pages: 160

Brand: Dell Pages: 190

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands