NEC Express5800/120Rh-2 User Manual Download | Manualshive

Page: 133 / 406

background image

Configuring Your Server 4-37

IMPORTANT:

To migrate the boot disk that contains an OS, refer to the "Migration
in NEC Express5800 Windows".

Make sure the copy source and copy destination. If they are
incorrect, the data will no longer be restored.

3.

Enter the desired RAID Name in [Assign RAID Name] window.

IMPORTANT:

RAID Name must be unique and up to 15 characters are acceptable.

If a valid partition information or a boot block is detected in the
selected hard disk drive or copy target disk drive, a warning
message will be displayed. Select [Yes] to continue creating an array,
[No] to terminate.

Take sufficient care not to select the proper hard disk drive or copy
destination drive. If not, the data will not be restored.

4.

The message "Do you want to make this array as bootable?" to prompt you to specify the
boot priority of the new array appears. Select [YES] to specify, or [NO] to ignore, and
then press

Enter

.

NOTE:

The boot priority can be changed after the arrays have been

created. To change priority, see "Boot Priority" described earlier.

5.

Select [Yes] for the message [Create Array?] and press

Enter.

Selecting [No] terminates creating an array and returns to the main menu.

6.

Select [Yes] for the message [Are you sure?] and press

Enter.

Selecting [No] terminates creating an array and returns to the main menu.

When an array has been created, build operation starts.

IMPORTANT:

Be sure to complete the Build process. Do not stop the

process by pressing

Esc

. OS detects only an array of which build

process has been completed and its status is "Optimal". In addition, no
OS can be installed in that array.

7.

Press

Esc

when the message [Build Completed] is displayed to return to the main menu.

NOTE:

On the main menu, make sure that "Optimal" is indicated for

the status of the created array.

IMPORTANT:

After creating an array, set the boot priority for the

created array according to "Boot Priority".

«
...
131
132
133
134
135
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

BladeCenter HS23

Brand: IBM Pages: 36

Serial Servers Vlinx VESR9xx

Brand: B&B Electronics Pages: 61

Express5800/R310e-E4

Brand: NEC Pages: 86

Brand: Premio Pages: 3

UltraNEXUS-HD X5

Brand: Leightronix Pages: 5

SUPERSERVER 5014C-MT

Brand: Supero Pages: 112

301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...

Brand: LaCie Pages: 74

ConnectPort LTS 16

Brand: Digi Pages: 169

Brand: Hitachi Pages: 208

Brand: Hitachi Pages: 36

RIP Station 5100

Brand: Epson Pages: 140

Maxtor Central Axis

Brand: Maxtor Pages: 2

TS-73AeU Series

Brand: QNAP Pages: 70

Brand: dallmeier Pages: 12

Brand: MAXDATA Pages: 2

Brand: MAXDATA Pages: 6

AcquiLite A7810

Brand: Obvius Pages: 29

Brand: Dataton Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands