NEC Express5800/120Rh-2 User Manual Download | Manualshive

Page: 216 / 406

background image

6-18 Installing and Using Utilities

NEC ESMPRO

The NEC ESMPRO (referred to as ESMPRO hereafter) lets a system administrator manage remote
servers across a network.    ESMPRO monitors server hardware and software configurations,
failures, and performance.    With log data collected by ESMPRO, a system administrator can track
long-term and short-term performance, monitor server usage, create graphs to record trends, and
check server failure rates.    The administrator can use the information collected to create more
efficient data routing procedures and optimize server usage.

IMPORTANT:

For installation procedure and detailed explanations on

NEC ESMPRO, refer to the online document in the NEC
EXPRESSBUILDER CD-ROM.

Functions and Features

The ESMPRO offers many functions and features for managing remote servers across a network.
These features help the system administrator perform daily system operation, system extension, and
transfer tasks. Some features of ESMPRO Manager include:

Hardware and software server configuration

–

Hardware resources mounted in servers, such as the CPU, memory, disks, disk arrays,
and LAN boards.

–

Software resources, such as operating system information and drivers running on each
server.

Server failures

–

On-screen real-time displays provide the system administrator with the failure type,
location, cause, and suggested corrective action.

–

Failure data includes hardware failure information such as system board temperature,
memory failure, crashes, and software failure information.

Performance

–

ESMPRO monitors server performance and displays server usage on the screen and
displays information, such as the rate of CPU load, memory usage, disk usage, and
LAN traffic. Usage threshold values can help the system administrator monitor and
prevent server overloads.

«
...
214
215
216
217
218
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

Brand: AXIOMTEK Pages: 55

callpilot 1002rp

Brand: Avaya Pages: 150

Brand: Olive Pages: 24

Brand: Digi Pages: 124

Brand: Digi Pages: 118

Brand: HP Pages: 94

Integrity rx5670

Brand: HP Pages: 46

Brand: HP Pages: 98

NetServer AA 4000

Brand: HP Pages: 82

Brand: HP Pages: 25

HPE ProLiant ML30 Gen9

Brand: HP Pages: 112

Brand: HP Pages: 28

Brand: HP Pages: 56

Hyper Converged 380

Brand: HP Pages: 125

Brand: HP Pages: 23

integrity rx2800 i4

Brand: HP Pages: 156

Brand: HP Pages: 7

Integrity BL860c i2

Brand: HP Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands