NEC Express5800/120Rh-2 User Manual Download

Page: 233 / 406

Maintenance 7-9

Select [System Diagnostics].

The System Diagnostics starts and completes in approximately three minutes.

When the diagnosis completes, the screen of the display changes in the following
indication.

[Enter] Detail Information [ESC] Return to Enduser Menu

Test End

TeDoLi(TEst & Diagnosis On Linux) Ver001.00(Build020901.1.1m)

MEM

Memory

16 count

NormalEnd

CACHE

Cache

49 count NormalEnd

<SCSI>
HDD_02:000 DK32DJ-36W

89 count

NormalEnd

Start10:06:58 End 10:09:58 Pass 000:03:00 TestTime 000:03:00
Test End : NormalEnd 03 AbnormalEnd 00 ForceEnd 00

Guide line

Test window

Test result

Test windows title

Diagnosis tool title

Diagnosis tool title: shows a name of this diagnosis and Version information.

Test windows title: shows the progress of diagnosis. When it completes, it shows "Test

End"

Test Result:

shows the information including time of start, end and progress, and
result of the diagnosis.

Guide line:

shows a description of keys to navigate the window.

Test window:

Move the cursor and press

Enter

to view the detail of the diagnosis.

If an error is detected during the System Diagnostics, the test result shows "Abnormal
End" in red color. Move the cursor and press

Enter

on the diagnosis which error

occurred. Take a note of the error message showed, and contact your service
representative.

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Search results

Summary of Contents for Express5800/120Rh-2

Reviews:

Related manuals for Express5800/120Rh-2

Brands by name

Popular brands

NEC Express5800/120Rh-2, User Manual

Search results

Summary of Contents for Express5800/120Rh-2

Reviews:

Related manuals for Express5800/120Rh-2

Brands by name

Popular brands