NEC Express5800/120Rh-2 User Manual Download | Manualshive

Page: 295 / 406

background image

Upgrading Your Server 9-21

Installation

Install a DIMM in the following procedure.

IMPORTANT:

The server supports DIMMs of only the low-profile

type (30 mm (1.2 inches) in height). It does not support DIMMs
exceeding the specified height.

1.

See the section "Preparing for Installation and Removal" described earlier to prepare.

2.

Pull out the server from the rack.

3.

Open the logic cover.

4.

Push the DIMM straight into the socket.

NOTE:

Make sure of the orientation of the DIMM.

Position the DIMM so that a notch in the bottom edge of the DIMM
aligns with the keyed socket. Applying too much pressure can damage
the socket. Keyed DIMMs insert only one way.

IMPORTANT:

To avoid damage to the socket, do not apply

excessive force while pressing the DIMM.

The levers automatically close when the DIMM is inserted into the socket.

5.

Install the components you removed in steps 1 to 3.

6.

Power on the server and verify that POST displays no error messages.

If POST displays an error message, take a note on the message and see the POST error
messages listed in Chapter 8.

7.

Start the SETUP and select [Advanced]

→

[Memory Configuration] to verify that the

installed DIMM shows the status "Normal". (See Chapter 4 or details.)

8.

Select "Yes" for [Reset Configuration Data] on the [Advanced] menu.

This setting is required to change the hardware configuration data. See Chapter 4 for
details.

9.

If the Windows operating system is in use, set the paging file size to the recommended
value (total memory size × 1.5) or a greater value. See Chapter 5 for details.

Key slot

Key

«
...
293
294
295
296
297
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

Brand: D-Link Pages: 38

Epress EtherNetwork DP-301P+

Brand: D-Link Pages: 2

Brand: 360 Systems Pages: 8

Brand: Xerox Pages: 24

DocuColor 7000AP

Brand: Xerox Pages: 36

Brand: Rack Solutions Pages: 8

Brand: TYAN Pages: 87

Brand: Advantech Pages: 38

DOMINION KSX II

Brand: Raritan Pages: 362

Brand: BCDVideo Pages: 157

DSTni-XPress DR

Brand: Lantronix Pages: 2

Brand: Inspur Pages: 196

Brand: Vingtor Stentofon Pages: 68

AS2041M-32R Plus

Brand: Supero Pages: 106

Brand: Tiger Technology Pages: 22

Brand: XVision Pages: 100

Multimedia Server MAX MMS-04S

Brand: AMX Pages: 2

Brand: Planet Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands