NEC Express5800/120Rh-2 User Manual Download | Manualshive

Page: 50 / 406

background image

2-18 General Description

SAF-TE LOGIC

NOTE:

SAF-TE Logic is in systems that include the hot-swap SCSI

disk drive cage. SAF-TE Logic is not available in systems that
include the standard SCSI disk drive cage.

The SCSI backplane includes SAF-TE (SCSI Accessed Fault Tolerant Enclosure) logic that provides
an interface to the disk subsystem that supports status signals, hot swapping drives, and enclosure
monitoring.

The transport mechanism for the standardized alert detection and status reporting is the SCSI bus.
Disk drives, power supplies, cooling fans, and temperature are continually monitored and the
conditions then reported over the SCSI bus to the system. When used with RAID management
software the user can be alerted of impending or imminent disk conditions requiring attention.
This allows the user to react to conditions that could normally go unnoticed until data loss.

SYSTEM BOARD FEATURES

The following subsections describe the system board major components.

Processor

The system board accommodates one or two Intel



Xeon



processors with 1MB cache in the

INT3/FCPGA socket package. This processor uses the .13 micron technology and offers advanced
performance. The processor external interface operates at a maximum of 800 MHz.

Memory

The system board contains six 240-pin DIMM slots each supporting 72-bit ECC (64-bit main
memory plus ECC) registered SDRAM DIMMs (DDR2 400 compatible). Memory is two-way
interleaved and partitioned in three groups. You may install a minimum of 1GB (512MB × 2) and as
much as 16 GB.

The controller automatically detects, sizes, and initializes the memory array, depending on the type,
size, and speed of the installed DIMMs, and reports memory size and allocation to the server via
configuration registers.

NOTE:

Use DIMMs that have been tested for compatibility with the

server board.
Contact your service representative or dealer for a current list of
approved memory modules.

«
...
48
49
50
51
52
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

Express5800/T110g-E

Brand: NEC Pages: 2

Brand: Acano Pages: 17

SUPERSERVER 6028TP-HTFR

Brand: Supero Pages: 141

Brand: Sun Microsystems Pages: 138

Brand: IBM Pages: 98

Brand: Vxl Pages: 19

BocaVision WT120

Brand: Boca Systems Pages: 28

Brand: Sun Microsystems Pages: 121

Express5800/E120d-1

Brand: NEC Pages: 4

Express5800/B140a-T

Brand: NEC Pages: 19

Express5800/B120f-h

Brand: NEC Pages: 21

Express5800/GT110b

Brand: NEC Pages: 27

Express5800/GT110e-S

Brand: NEC Pages: 34

Express5800/B110d

Brand: NEC Pages: 19

Express5800/A2040d

Brand: NEC Pages: 20

Express5800/D120h

Brand: NEC Pages: 35

Express5800/A1040e

Brand: NEC Pages: 59

Express5800/A1040c

Brand: NEC Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands