NEC Express5800/120Rh-2 User Manual Download | Manualshive

Page: 55 / 406

background image

General Description 2-23

SYSTEM SECURITY

To help prevent unauthorized entry or use of the system, the system includes a full lockable front
bezel and Server Management software that monitors the front bezel intrusion switch.

Security with Mechanical Locks and Monitoring

To unlock the bezel, insert the key in the lock and turn the lock counterclockwise until it stops
(about a quarter turn). The bezel is now unlocked and can be opened again.

To lock the bezel, insert the key in the lock. Turn the lock clockwise until it stops (about a quarter
turn). The bezel is now locked and cannot be opened.

Software Locks via the BIOS Setup Utility

The BIOS Setup Utility provides a number of security features to prevent unauthorized or accidental
access to the system. Once the security measures are enabled, you can access the system only after
you enter the correct password(s). For example:

Enable the keyboard lockout timer so that the server requires a password to reactivate the
keyboard and mouse after a specified time out period – 1 to 120 minutes.

Set and enable a supervisor password.

Set and enable a user password.

Set secure mode to prevent keyboard or mouse input and to prevent use of the front panel
reset and power switches.

Activate a hot key combination to enter secure mode quickly.

Disable writing to the diskette drive when secure mode is set.

Disable access to the boot sector of the operating system hard disk drive.

«
...
53
54
55
56
57
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

Univerge SV8100

Brand: NEC Pages: 2

Brand: Aastra Pages: 502

Brand: IBM Pages: 100

Brand: Fujitsu Pages: 200

CallPilot 1005r

Brand: Nortel Pages: 74

Communication Server 100

Brand: Nortel Pages: 214

Brand: Intermec Pages: 144

Brand: Intermec Pages: 452

AirProjector KJ-200

Brand: TriLink Pages: 56

IMS LANTIME M500

Brand: Meinberg Pages: 132

Brand: Sierra Wireless Pages: 53

Brand: Supero Pages: 130

Brand: Tektronix Pages: 50

Brand: Vlinx Pages: 43

Brand: Inventec Pages: 258

Brand: Xiva Pages: 41

Brand: Gigabyte Pages: 149

Brand: MPC Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands