NEC Express5800/120Rh-2 User Manual Download | Manualshive

Page: 57 / 406

background image

General Description 2-25

Summary of Software Security Features

The table below lists the software security features and describes what protection each offers. In
general, to enable or set the features listed here, you must run the BIOS Setup and go to the Security
Subsystem Group, menu. The table also refers to the Setup utility.

Software Security Features

Feature

Description

Secure mode

How to enter secure mode:

•

Setting and enabling passwords automatically places the system in
secure mode.

•

If you set a hot-key combination (through Setup), you can secure the
system simply by pressing the key combination. This means you do not
have to wait for the inactivity time-out period.

When the system is in secure mode:
The server can boot and run the operating system, but mouse and
keyboard input is not accepted until the user password is entered.
At boot time, if a CD is detected in the CD-ROM drive or a diskette in drive
A, the system prompts for a password. When the password is entered, the
server boots from CD or diskette and disables the secure mode.
If there is no CD in the CD-ROM drive or diskette in drive A, the server
boots from drive C and automatically goes into secure mode. All enabled
secure mode features go into effect at boot time.
To leave secure mode: Enter the correct password(s).

Disable writing to
diskette

In secure mode, the server will not boot from or write to a diskette unless a
password is entered.
To write protect access to diskette whether the server is in secure mode or
not, use the Setup main menu, Floppy Options, and specify Floppy Access
as read only.

Set a time out period
so that keyboard
and mouse input are
not accepted.
Also, screen can be
blanked, and writes
to diskette can be
inhibited

Specify and enable an inactivity time out period of from 1 to 120 minutes.
If no keyboard or mouse action occurs for the specified period, attempted
keyboard and mouse input will not be accepted.
The monitor display will go blank, and the diskette drive will be write
protected (if these security features are enabled through Setup).
To resume activity: Enter the correct password(s).

Control access to
using the BIOS
Setup: set
supervisor password

To control access to setting or changing the system configuration, set a
supervisor password and enable it through Setup.
If both the supervisor and user passwords are enabled, either can be used
to boot the server or enable the keyboard and/or mouse, but only the
supervisor password will allow Setup to be changed.
To disable a password, change it to a blank entry in the Change Password
menu of the Supervisor Password Option menu found in the Security
Subsystem Group.
To clear the password if you cannot access Setup, change the Clear
Password jumper (see Chapter 4).

«
...
55
56
57
58
59
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

SUPERSERVER 6021F

Brand: Supermicro Pages: 116

UniServer R6900 G5

Brand: H3C Pages: 17

Eserver xSeries 360 Type 8686

Brand: IBM Pages: 74

Eserver 345 Series

Brand: IBM Pages: 70

Brand: AXIOMTEK Pages: 58

x3350 - System - 4192

Brand: IBM Pages: 98

x3500 - System - 7977

Brand: IBM Pages: 124

Brand: IBM Pages: 106

x3200 - System M3 - 7328

Brand: IBM Pages: 100

System x3400 Type 7975

Brand: IBM Pages: 124

System x3300 M4

Brand: IBM Pages: 470

System x iDataPlex dx360

Brand: IBM Pages: 26

Brand: BRONKHORST Pages: 19

Brand: Sony Pages: 8

BSV-M1 - StorStation NAS Server

Brand: Sony Pages: 58

60 Business Phone

Brand: ESI Pages: 2

TalkAnytime TA2410

Brand: Multitech Pages: 235

Brand: LG-Ericsson Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands