Home
/
NEC
/
Express5800/320Fd-MR
/
User Manual

NEC Express5800/320Fd-MR, User Manual

Share

Page: 322 / 484

background image

5-124 Installing and Using Utilities

To configure a custom action

1.

On the Custom Actions page, do one of the following:

•

Next to

File

, type the full path name and file name of the executable you want to run.

The file must already exist on the system.

Example: C:\bin\mybatchfile.bat

•

Click

Browse

to locate the executable using a file browser. Click the file name in

the file browser, and click Open to select the file.

2.

Next to

Arguments

, type any arguments that you need to run with your executable.

No arguments are required; however, see “Programming Notes for Custom Actions” on page
5-126 for information about passing optional Active Upgrade environment variables to your
executable.

3.

In the drop-down list for

Control type

, select the option that best describes when the Active

Upgrade Console will execute your custom action, as discussed in the below table.

Control Types for Custom Actions

Control Type

Purpose

Start Application

Executes the custom action whenever the Active Upgrade Console needs
to start applications. For example, the console needs to restart
applications on the Upgrade Side when you merge the system.

Stop Application

Executes the custom action whenever the Active Upgrade Console needs
to stop applications. For example, the console needs to stop applications
on the Upgrade Side when you split the system. It also stops applications
on the Production Side when you merge the system.

Readiness Check

Executes the custom action once during the readiness check, before you
initiate the Active Upgrade process. This control type allows you to build
your own verifications into the readiness check.

«
...
320
321
322
323
324
...
»

Summary of Contents for Express5800/320Fd-MR





































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/320Fd-MR

Brand: 360 Systems Pages: 8

Brand: Xerox Pages: 220

Brand: Xerox Pages: 28

DocuPrint 100MX

Brand: Xerox Pages: 2

Brand: Omneon Pages: 2

Brand: IBM Pages: 106

Brand: Digital Equipment Pages: 15

Brand: Airlink101 Pages: 36

ZXCLOUD R5300 G3

Brand: Zte Pages: 19

Brand: Thecus Pages: 94

Brand: Leightronix Pages: 22

Brand: SAFARI Montage Pages: 5

Brand: Dataton Pages: 37

Brand: Octagon Pages: 17

Brand: Meinberg Pages: 4

Multi-Port Fast Ethernet Print Server FPS-3121

Brand: Planet Pages: 12

Brand: QNAP Pages: 16

Snap Server 18000

Brand: Adaptec Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands