background image

Configuring Optical Fibre Channel PCI Adapters

3-6

Express5800/320Ma: PCI Adapter Guide

 

Figure 3-2. LC Connector of a Fibre Channel Optical Cable 

Configuring Optical Fibre Channel PCI Adapters 

The manufacturer configures the internal settings for each optical Fibre Channel PCI 
adapter before the adapters arrive at your site. The U525 PCI adapters are configured 
to attach to a SAN or switch. The U526 PCI adapters are configured to attach directly 
to a storage system.

For information about configuring the EMC storage systems, see the EMC 
documentation supplied with the storage system.

Installing Optical Fibre Channel PCI Adapters

Before installing the optical Fibre Channel PCI adapters, you must download the 
required driver and software updates from the Web as described in 

“Software 

Requirements of Optical Fibre Channel PCI Adapters” on page 3-4

.

N O T E

If you are installing optical Fibre Channel PCI adapters in 
a production system, you must schedule downtime for the 
following procedure. Though it is possible to remove the 
I/O enclosures from certain systems and physically install 
the adapters without shutting down the entire system, you 
must still reboot the system when you install the EMC 
PowerPath Software and any applicable software 
updates.

To install the adapters

1. Install any applicable Microsoft hotfix software updates required by the storage 

system.

2. Shut down the system.

mpci083

Summary of Contents for Express5800/320Ma











































































Reviews: