1. POST Error Message
Express5800/R110i-1, T110i-S, T110i Maintenance Guide
190
Chapter 3 Appendix
(1) Error
messages
(1/5)
Error Message
Description
Action
8000
System variable is
corrupted.
BIOS settings are invalid.
Run BIOS Setup Utility (SETUP), and then select
Load Setup Defaults
and specify the necessary
settings.
8002
Check date and time settings
The real-time clock is incorrect.
Run SETUP, and then specify the correct date and
time.
8006
System configuration data
cleared by Jumper.
The setup utility settings were
cleared by the jumper.
See
Chapter 1 (7. Resetting and Clearing the
Server).
Start SETUP, and then setup each item
again. This error message may appear when
lithium battery is removed.
8007
SETUP Menu Password cleared
by Jumper.
The setup utility password was
cleared by the jumper.
See
Chapter 1 (7. Resetting and Clearing the
Server).
Start SETUP, and then set password
again.
8020
BIOS update error.
BIOS update failed.
Try again. This is an error logged when BIOS is
updated. If the same error occurs again, see the
error information described in the release note of
BIOS to fix the error.
8021
Recovery jumper is set, but
recovery images is not
found.
The recovery jumper is set but the
BIOS recovery failed.
Contact your sales representative.
8800
DXE_NB_ERROR
An error was detected during
initialization of the chipset
8801
DXE_NO_CON_IN
An error was detected during
initialization of the console.
8802
DXE_NO_CON_OUT
8803
PEI_DXE_CORE_NOT_FOUND
Malfunction of the flash memory
for system, or error is detected on
the early stage of system start-up.
8804
PEI_DXEIPL_NOT_FOUND
8805
DXE_ARCH_PROTOCOL_NOT_A
VAILABLE
8808
DXE_FLASH_UPDATE_FAILED
The Flash ROM was not written
correctly.
8830
PEI_RECOVERY_NO_CAPSULE
The Flash ROM was not
recovered correctly.
8831
PEI_RECOVERY_PPI_NOT_FO
UND
8832
PEI_RECOVERY_FAILED
9000
Unsupported CPU detected
An unsupported CPU was
detected.
9E80
Forced to use CPU with error.
A CPU error occurred.
AB00
Memory not detected
No valid memory is installed.
Check if the memory modules are properly
installed.
AE01
DIMM1 has been disabled.
A memory error occurred. DIMM1
has been disabled.
Contact your sales representative.
AE02
DIMM2 has been disabled.
A memory error occurred. DIMM2
has been disabled.
AE03
DIMM3 has been disabled.
A memory error occurred.
DIMM3 has been disabled.
AE04
DIMM4 has been disabled.
A memory error occurred.
DIMM4 has been disabled.
AE81
DIMM1 with error is enabled.
An error in DIMM1 occurred.
The DIMM1 was forcibly enables
because all memory is currently
disabled.
AE82
DIMM2 with error is enabled.
An error in DIMM2 occurred.
The DIMM2 was forcibly enables
because all memory is currently
disabled.
B000
Expansion ROM not
initialized
There is no memory for expanding
option ROM.
If the PCI board does not connect to a bootable
device, disable the
Option ROM Scan
for that
board.
B001
Expansion ROM not
initialized - PCI Slot 1
(Express5800/T110i,
T110i-S)
Option ROM expansion in PCI slot
1 failed.
If the PCI board does not connect to a bootable
device, disable the
Option ROM Scan
for that
board.
Run SETUP, select
Advanced
Serial Port
Configuration
, and specify the different settings
for
Serial Port A
and
Serial Port B
.
Expansion ROM not
initialized - PCI Slot 1B
(Express5800/ R110i-1)
Option ROM expansion in PCI slot
1B failed.
