Express5800/R120h-2M
First Edition,
July 2020
Be sure to read this guide carefully before using this
server and retain it for reference.
This document provides information required to use your server safely and properly.
Keep this document nearby so that you may refer to it as necessary. Before using this server, be sure to read
this guide and “
User’s Guide
” (
User’s Guide
is available at NEC Web Site “http://www.58support.nec.co.jp/
global/download/”). It is recommended to keep the firmware of this server updated. For details of names in this
document, refer to
Names and Functions of Parts
in the “
User’s Guide
”.
The following describes the procedures from opening the carton box to
starting using this product. Be sure to follow these steps.
Step 1
Check the accessories.
Open the carton box, and then make sure you have all the accessories listed below:
These accessories are required for setup and maintenance. Please keep them in a safe
place.
●
Getting Started (This guide) × 1
●
Rack rail (Selection required option) × 2
●
Safety Precautions and Regulatory Notices × 1
●
Front Bezel × 1
●
Security key (attached to Front Bezel) × 2
●
Test & Diagnostic Tool CD × 1
Important: For set models and BTO (Build to Order) products, see also “List of
Embedded Products and Accessories”.
Step 2
Install internal optional devices.
Install internal optional devices. (Go to Step 3 if you have not purchased options.)
Note: See
Installing Internal Optional Devices
in the “
User’s Guide
” and the guide provided with the
optional device.
Step 3
Place the product to a proper location.
Determine the location to place this product.
Set up a rack in an appropriate place, and then mount the server in the rack.
Note: See
Installation and Connection
in the “
User’s Guide
”.
CAUTION: Please do not use this equipment in the environment that contains
corrosive gases (Sulfur dioxide (SO
2
), hydrogen sulfide (H
2
S), nitrogen
monoxide (NO), nitrogen dioxide (NO
2
), chlorine (Cl), ammonia (NH
3
),
ozone (O
3
)), or the environment exists components (salt or Sulphur) that
aggravate corrosion.
Step 4
Connect cables.
Connect the cables to the server.
Note: The figures below are reference diagrams including optional devices added.
See
Installation and Connection
in the “
User’s Guide
”.
*1 Connect the power cord to a circuit breaker of up to 15 A.
Getting Started!
• Keep proper po
s
t
u
re
• Adj
us
t the
a
ngle,
b
rightne
ss
,
a
nd contr
as
t of the
di
s
pl
a
y to
su
it yo
u
r preference
s
.
Tips for your health and safety
U
s
ing
a
comp
u
ter exten
s
ively m
a
y
a
ffect different p
a
rt
s
of yo
u
r
b
ody. Here
a
re tip
s
yo
u
s
ho
u
ld
follow while working on
a
comp
u
ter to minimize
s
tr
a
in on yo
u
r
b
ody.
• T
a
ke
a
b
re
a
k. Light exerci
s
e i
s
a
l
s
o recommended.
• Adj
us
t the
a
ngle of key
b
o
a
rd
The environment th
a
t
sa
ti
s
fie
s
the
following condition
s
<Oper
a
ting>
Am
b
ient temper
a
t
u
re:
10˚C to 35˚C
H
u
midity:
8
% to 90%
Temper
a
t
u
re gr
a
dient: ±10˚C/ho
u
r
Air pre
ssu
re: 749 to 1040 hp
a
O
u
tlet or UP
S
within
re
a
ch of the power cord
100/200 VAC two-prong
gro
u
nded o
u
tlet or UP
S
On the fl
a
t
a
nd ro
bus
t
b
o
a
rd
Do not
us
e in the environment where
corro
s
ive g
as
i
s
gener
a
ted.
There m
us
t
b
e 1 m cle
a
r
a
nce in
front
a
nd
b
ehind the
u
nit, 60 cm
on e
a
ch
s
ide,
a
nd 40 cm
ab
ove.
When in
s
t
a
lling
m
u
ltiple r
a
ck
s
,
b
e
su
re to
a
nchor them
together.
Att
a
ch
s
t
ab
ilizer
s
.
User’s Guide
User’s Guide
is available at NEC Web Site
“https://www.58support.nec.co.jp/global/download/”.
Search the product manual by the model number of the server you purchased.
REAR
Device with serial interface
USB
3
.0 device
Display unit
Finally, connect the provided
power cord to an outlet *1
1000BASE-T/
100BASE-TX/
10BASE-T
Management
LAN port
8x 2.5-inch drive model
USB device
FRONT
8x
3
.5-inch drive model
