background image

English-15

English

Specifi cations

Monitor Specifi cations

MultiSync E223W

Notes

LCD Module 

Diagonal:

 

Viewable Image Size:

 

Native Resolution (Pixel Count): 

55.87 cm/22.0 inches 
55.87 cm/22.0 inches 
1680 x 1050

Active matrix; thin fi lm transistor (TFT) liquid crystal 
display (LCD); 0.282 mm dot pitch; 250 cd/m

2

 white 

luminance; 1000:1 contrast ratio (typical), (25000:1 
Contrast ratio, Dynamic).

Input Signal

DisplayPort: 

DisplayPort Connector:

Digital RGB 

DisplayPort Complies with Standard V1.1a, 
applicable to HDCP

DVI: 

DVI-D 24pin:

Digital RGB

DVI (HDCP)

VGA: 

15pin Mini D-sub:

Analog RGB
Sync

0.7 Vp-p/75 ohm
Separate sync.TTL level Positive/Negative
Composite sync.TTL level Positive/Negative
Sync on Green 
(Video 0.7 Vp-p and Sync Negative 0.3 Vp-p)

Display Colours

16,777,216

Depends on display card used.

Synchronization Range  

Horizontal:

  

Vertical:

31.5 kHz to 82.3 kHz (Analog)
31.5 kHz to 82.3 kHz (Digital)
56 Hz to 75 Hz

Automatically
Automatically
Automatically

Viewing Angle 

Left/Right:

 Up/Down:

±85° (CR > 10)
±80° (CR > 10)

Image Formation Time

5 ms (Typ.)

Resolutions Supported

720 x 400*

1

: VGA text 

  Some systems may not support all modes listed.

640 x 480*

1

 at 60 Hz to 75 Hz

800 x 600*

1

 at 56 Hz to 75 Hz

832 x 624*

1

 at 75 Hz

1152 x 864*

1

 at 75 Hz

1024 x 768*

1

 at 60 Hz to 75 Hz

1152 x 870*

1

 at 75 Hz

1280 x 960*

1

 at 60 Hz to 75 Hz

1280 x 1024*

1

 at 60 Hz to 75 Hz

1400 x 1050*

1

 at 60 Hz to 75 Hz

1440 x 900*

1

 at 60 Hz 

  NEC DISPLAY SOLUTIONS cites recommended

1680 x 1050 at 60 Hz........................................... resolution for optimal display performance.

Active Display Area 

Landscape: Horiz.:

 Vert.:
  

Portrait: Horiz.:

 Vert.:

473.8 mm/18.7 inches
296.1 mm/11.7 inches
296.1 mm/11.7 inches
473.8 mm/18.7 inches

Power Supply

AC 100-240 V ~ 50/60 Hz

Current Rating

0.45 - 0.25 A

Dimensions  

Landscape:

  

Portrait:

 Height 

Adjustment:

503.5 mm (W) x 383.3 - 493.3 mm (H) x 213.9 mm (D)
19.8 inches (W) x 15.1 - 19.4 inches (H) x 8.4 inches (D)
329.7 mm (W) x 519.9 - 575.7 mm (H) x 213.9 mm (D)
13.0 inches (W) x 20.5 - 22.7 inches (H) x 8.4 inches (D)
110 mm / 4.3 inches

Weight

4.9 kg (10.8 lbs)/Without stand: 3.2 kg (7.1 lbs)

Environmental Considerations
 Operating 

Temperature:

  

Humidity:

 Altitude:
 Storage 

Temperature:

 Humidity:
 Altitude:

5°C to 35°C/41°F to 95°F
20% to 80%
0 to 6,562 Feet/0 to 2,000 m
-10°C to 60°C/14°F to 140°F
10% to 85%
0 to 40,000 Feet/0 to 12,192 m

*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is normal and 
necessary for all current fl at panel technologies when displaying non-native resolutions full screen. In fl at panel technologies, each dot on the screen is actually one 
pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.

NOTE: 

Technical specifi cations are subject to change without notice.

Summary of Contents for MultiSync E223W






















Reviews: