E-5
INTRODUCTION
1
This section introduces you to your new MultiSync MT830
(SVGA) / 1030 (XGA) LCD Projector, provides a list of
materials that comes with your projector and describes the
features and controls.
Congratulations On Your Purchase Of The
MultiSync
MT830/1030 LCD Projector
The MultiSync MT830/1030 is one of the very best LCD
projectors available today. The multiple LCD panels enable
you to project precise images up to 300 inches (762 cm)
across (measured diagonally) from your PC or Macintosh
computer (desktop or notebook), VCR, DVD player, docu-
ment camera, or even a laser disc player.
You can use the projector on a tabletop or cart, you can
permanently mount it on a ceiling*
1
, or you can use
MultiSync MT830/1030 LCD Projector to project images
from behind the screen. The remote control can be used
wirelessly or with a cable, and you can even use the remote
control with the built-in remote mouse receiver to operate the
mouse on your PC or Mac. But best of all, the MultiSync
MT830/1030 is an NEC LCD projector. That means you can
depend on years of reliable performance and crystal-clear
presentations!
Features you’ll enjoy:
•
Simple set up and operation.
•
Hot air blown from the vents does not bother the audience
during your presentation since the vents are located on the
front.
•
A high-performance 150 watt short arc high pressure lamp
that delivers 1000 ANSI lumens (MT1030: 900 ANSI
lumens) and an operating lamp life is 2000 hours.
•
A wireless remote control that operates the projector from
any angle.
•
A laser pointer that' s built into the remote control.
•
The power zoom control enables you to adjust the image
to be between 50.8 and 762 cm (measured diagonally).
•
Keystone correction allows you to correct trapezoidal dis-
tortion so that the image is square.
•
White balance control allows you to adjust the brightness
and contrast for each RGB color.
•
You can choose between video modes depending on your
source: "normal" for a typical picture, "natural" for true
color reproduction, and "camera" for use with a document
camera or low APL picture.
•
The optional MT Viewer kit allows you to start your
presentation even when a PC is not available at the site.
•
The "image capture" enables you to use the entire picture
as a background image or to create slides (optional MT
Viewer required).
•
An image can be projected from in front or behind a
screen, and the projector can even be installed on the
ceiling.
•
NEC Technologies' exclusive AccuBlend intelligent pixel
blending technology - an extremely accurate image com-
pression technology - offers a crisp image with SXGA
(1280
2
1024) resolution*
3
. You can select any point on
the screen with the pointer and enlarge the selected area.
•
Supports most IBM VGA, SVGA, XGA, SXGA(with
AccuBlend)*
3
, Macintosh, or any other RGB signals within a
horizontal frequency range of 15.625 to 85 kHz and a vertical
frequency range of 50 to 85 Hz. This includes NTSC, PAL,
SECAM and NTSC4.43 standard video signals.
Note: Composite video standards are as follows:
NTSC:
U.S. TV standard for video in U.S. and Canada.
PAL:
TV standard used in western Europe.
SECAM:
TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
•
The remote control can be used with or without a cable,
and you can even use the remote to operate your PC or
Macintosh mouse wirelessly from across the room with
the built-in remote mouse receiver.
•
You can control your MultiSync MT830/1030 LCD Pro-
jector with a PC.
•
The contemporary cabinet design is compact, easy to
carry, and complements any office, board room or audito-
rium.
•
Eight kinds of pointers are available for your presentation.
*
1
Installing the MultiSync MT830/1030 LCD Projector on
the ceiling must be done by authorized NEC technicians.
Consult your NEC dealer for more information.
*
2
An XGA image (1024
2
768) is converted into an
800
2
600 crisp image with NEC technology's AccuBlend.
*
3
An SXGA image (1280
2
1024) is converted into a
1024
2
768 crisp image with NEC technology's
AccuBlend.
