English-36
DAYLIGHT SAVING
Sets daylight savings on or off.
NOTE: Please set the [TIME & DATE] setting first if you change the [DAYLIGHT SAVING] setting.
DAYLIGHT SAVING
If [ON] is selected, please set daylight savings settings below.
BEGIN MONTH
Set daylight savings beginning date.
END MONTH
Set daylight savings ending date.
TIME DIFFERENCE
Set the time difference.
OFF TIMER
Set the monitor to power off after a preset time period. A time period between 1 to 24 hours may be set.
NOTE: [SCHEDULE] is not available if [OFF TIMER] is [ON].
RESET
Resets the following settings within the [SCHEDULE] menu back to factory setting: [DATE & TIME] and
[DAYLIGHT SAVING].
MULTI INPUT
KEEP MULTI PICTURE
MODE*
1
Allows the monitor to remain in [MULTI PICTURE] and [TEXT TICKER] mode after powering off.
When Power is returned, [MULTI PICTURE] and [TEXT TICKER] appear without having to enter the OSD.
MULTI PICTURE MODE*
1,
*
3
Selects picture number and display form.
MULTI PICTURE
When [OFF] is selected, one picture is displayed.
When [ON] is selected, several pictures are displayed. Select [PIP] or [PBP].
NOTE: When [ON] is selected, [TEXT TICKER], [TILE MATRIX], [MOTION] in [SCREEN SAVER], [IMAGE FLIP]
except for [NONE], [SUPER] in [INPUT CHANGE] is released.
PICTURE NUMBER
Selects [2 PICTURES], [3 PICTURES], [4 PICTURES].
After selected [PICTURE NUMBER], select display form [PIP], [PBP1], [PBP2], or [PBP3]. Depending on the
setting at [PICTURE NUMBER], display form selection is changed.
PICTURE NUMBER: 2 PICTURES
PIP
PBP1
A
B
A
B
PICTURE NUMBER: 3 PICTURES
PIP
PBP1
PBP2
PBP3
A
C
B
C
B
A
C
B
A
B
A
C
PICTURE NUMBER: 4 PICTURES
B
A
C
D
A: PICTURE 1 B: PICTURE 2
C: PICTURE 3 D: PICTURE 4
ACTIVE PICTURE*
1,
*
2
ACTIVE
When [MULTI PICTURE] is [OFF], [PICTURE 1] is the Active Picture. When [MULTI PICTURE] is [ON], sets
Active Picture.
NOTE: This function depends on [MULTI PICTURE] setting.
ACTIVE FRAME
The active picture is shown within a red frame.
INPUT SELECT*
1,
*
2,
*
3
Selects the Multi Picture input. Press the + button or - button to select the input.
NOTE: This function is not available when [MULTI PICTURE] is [OFF].
When changing input signal for the active picture, after selecting an input press the SET button.
PICTURE SIZE*
1,
*
2,
*
4
Sets the Active Picture size.
Press the SET/POINT ZOOM button to adjust the picture size. Press + or CH+ to expand. Press - or CH- to reduce.
NOTE: This function is not available when [MULTI PICTURE] is set to [4 PICTURES].
Depends on the setting at [MULTI PICTURE MODE], some pictures cannot change their size.
PICTURE POSITION*
1,
*
2,
*
4
Sets the Active Picture location.
Pressing the + button moves the Active Picture to the right, and pressing the - button moves it to the left.
Pressing the
p
button moves the Active Picture up, and pressing the
q
button moves it down.
ROTATE
When [ON] is selected, all pictures rotate.
When [OFF] is selected, sets each picture [ROTATE] settings.
NOTE: When [TEXT TICKER], [IMAGE FLIP] except for [NONE], [STILL] is [ON] or [SCREEN SAVER] is active,
this function is not available. If [1:1] is selected in [ASPECT], characters and lines may be displayed in blurring,
depending on the signal resolution.
When [ROTATE] is [ON], POINT ZOOM and [IMAGE FLIP] except for [NONE] are not available.
Each picture [ROTATE] settings are released when [MULTI PICTURE] is set to [OFF].
When input signal is Interlace, the image may be distorted.
When [HDMI] of the [TERMINAL SETTINGS] is set to [MODE2], or [3 PICTURES] or [4 PICTURES] is selected
at [PICTURE NUMBER] in [MULTI PICTURE MODE], [ROTATE] is not available.
If [ROTATE] of [MULTI PICTURE CONTROL] is selected in the input signal with a high refresh rate, the image
may not be displayed smoothly. To reduce this condition please set the input signal with a low refresh rate.
PICTURE ASPECT*
1,
*
2,
*
4
Selects the Active Picture frame aspect.
To change aspect ratio of the screen image see
.
*1: This function is released when selecting [SUPER] in [INPUT CHANGE], [MOTION] in [SCREEN SAVER], [TILE MATRIX] and [IMAGE FLIP] except for [NONE].
*2: When [TEXT TICKER] is active or [MULTI PICTURE] is [OFF], this function is not available.
*3: When you select [OPTION] for multi picture input, this function depends on which Option Board you are using.
*4: This function is not available if [PIP] is set at [MULTI PICTURE MODE] and then [PICTURE1] is set at [ACTIVE PICTURE].
