NEC NP06CM Installation And Adjustment Manual Download | Manualshive

Page: 14 / 16

background image

14

Air intake on bottom panel

Wing nut

Dust cover

Cleaning the filter

To clean the filter of the air intake on the projector's bottom panel, remove the wing nut, then

slide the dust cover and remove it.

Now insert the tip of a vacuum cleaner and vacuum over the air intake.

After cleaning the filter, set the dust cover back in its original position and tighten the wing

nut.

• Be sure to turn off the power when cleaning the filter.
• For details on filter cleaning, see the projector's user's manual.

NP06CM-E 07.3.20 9:02 AM ページ 14

«
...
12
13
14
15
16
»

Summary of Contents for NP06CM

















Reviews:

No comments

Related manuals for NP06CM

Brand: AAXA Technologies Pages: 2

Brand: NEC Pages: 159

Brand: NEC Pages: 2

Brand: NEC Pages: 2

Brand: GEARGO Pages: 60

Brand: Christie Pages: 4

Brand: ViewSonic Pages: 43

Brand: Nebula Pages: 74

Brand: Optoma Pages: 75

PJ506D - SVGA DLP Projector

Brand: ViewSonic Pages: 41

Brand: Tripp Lite Pages: 3

E-VISION 4500 series

Brand: Digital Projection Pages: 30

Brand: Panasonic Pages: 72

Brand: Panasonic Pages: 62

Brand: Panasonic Pages: 138

Brand: Panasonic Pages: 221

Brand: Panasonic Pages: 129

TX-51GF85 series

Brand: Panasonic Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands