NEC NP06CM Installation And Adjustment Manual Download | Manualshive

Page: 8 / 16

background image

8

3

Suspend the Projector from the Fixed Ceiling Part

Slide the slotted part of the projector mounting adapter over the pin of the fixed ceiling
part and push all the way to the back.
The projector is temporarily suspended in this condition and attention must be paid so
that the unit does not fall since it is not fixed in place.

Slotted part of mounting adapter

Pin of fixed ceiling part

4

Temporarily Fasten the Projector Mounting Adapter

Temporarily fasten by partially tightening the four supplied (M5) screws.
Tighten firmly after completing the screen projection angle adjustment.

Mounting the Projector

Temporarily fasten also the other side.

NP06CM-E 07.3.20 9:02 AM ページ 8

«
...
6
7
8
9
10
...
»

Summary of Contents for NP06CM

















Reviews:

No comments

Related manuals for NP06CM

220OVATIONFTD55WW

Brand: Chauvet Professional Pages: 28

Harry the hedgehog

Brand: ZAZU Pages: 23

Brand: Optoma Pages: 75

Brand: SHOWTEC Pages: 36

Brand: Retual Pages: 7

STILFORD JBSC129WBK

Brand: Officeworks Pages: 17

VS-50111, VS-60111, WT-42311,

Brand: Mitsubishi Pages: 79

Brand: Runco Pages: 37

Brand: Optoma Pages: 2

EDGE FREE CLR 4

Brand: Akia Screens Pages: 8

Brand: Panasonic Pages: 72

Brand: Action Pages: 40

Brand: Sanyo Pages: 1

Brand: Sanyo Pages: 1

Brand: Sanyo Pages: 68

Brand: Sanyo Pages: 52

Brand: Sanyo Pages: 52

Brand: Sanyo Pages: 77

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands