Installation Instructions
1.
The described Slot-in PC (STv2) has been designed according to the electronic, mechanical and thermal specifications of the OPS Standard, (Open Pluggable Specification), developed by Intel.
2.
For certain NEC public displays an NEC dual slot adapter is necessary for the OPS module to fit into the display.
Please have a look at the user manual and/or datasheet of your public display to confirm whether an adapter is needed or not. If the display is advertised as being a “Dual Slot” then an adapter will be needed. However, if the
manual/datasheet states the display is “STv2” only, then no adapter will be required.
3.
Please switch off the public display, projector or standalone adapter completely using the hard on/off switch or disconnect the equipment fully from the mains, before inserting the Slot-in PC.
4.
The Slot-in PC has to be inserted in the appropriate OPS (STv2) Slot or Dual Slot Adapter. (Picture 3A / 3B)
5.
The Slot-In PC starts up automatically after turning on the public display.
6.
The Slot-In PC controls its own fan plus the fan of the public display independently according to the thermal circumstances. At low temperatures, and if the CPU workload is low, the fans may not activate.
This is a normal procedure and not classified as a failure.
7.
If the Slot-In PC is equipped with a WIFI option, please ensure to attach the antenna to the WIFI connector on the Slot-In PC. It is recommended to affix the antenna at the end of the installation in order to avoid damages.
8.
Please note Aaronn Electronic GmbH or the resellers are liable for any data loss.
Installation Steps for NEC Displays of the XS series
Installation Steps for NEC Displays with STv1/Stv2 Slot (Dual Slot)
Picture 5
DUAL SLOT STv2 ADAPTER (SB-02AMW),
Order Code 100012868
Aaronn Electronic GmbH, Zeppelinstrasse 4, 82178 Puchheim, Germany.
All Rights Reserved
. All specifications are subject to change without notice.
Picture 1A
Picture 2A
Picture 3A
Picture 4A
For some public displays it might be necessary to
take off the handles on the side of the display, in
order to insert the
Slot-in PC. Therefore, please
loosen or remove the Phillips screw holding the
handle in place. Remove the slot covering plate, by
releasing 2 Phillips screws.
For some public displays the back of the Slot-in PC is
not covered fully by the display itself (e.g.MultiSync
X401S). For these displays a back covering plate is
included, which covers the fan on the Slot-In PC,
making it inaccessible.
Please make sure that the Slot-in PC is always
inserted in the right way. NOTE: The fan of the Slot-
in PC should always be facing away from the front of
the display. Please insert the Slot-in PC in the slot
very carefully until you feel a latching of the 2
connectors.
Do not use too much force, as this could damage the
Slot-In PC and/or the slot itself.
Use the screw, which was taken out with the
covering plate before, in order to secure the Slot-in
PC. Please re-affix the displays carrier handle, if
needed. Please make sure that the screws are
tightened correctly (1.39 to 1.89 N full-load).
Picture 1B
Picture 2B
Picture 3B
Picture 4B
Remove the covering plate which covers the slot
by loosening the two Phillips screws.
In order to use the STv2 devices a Dual Slot Stv2
Adapter is necessary (Picture 5). Please insert the
adapter with the right guidance (the open side
shows to the backside of the display).
Secure the adapter with the same screws taken
out in step 1.
Please make sure that the Slot-in PC is inserted in
the right guidance. Please note that the fan of the
Slot-in PC always has to be facing away from the
display. Please insert the option in the slot
carefully until you feel it latching to the internal
connector.
Please ensure too much force is applied as this
could damage the slot
Fix the Slot-in PC with the screws which are
also fixed at the covering plate.
Other languages of this document, drivers and information, can be found at:
Andere Sprachen dieses Dokumentes, Treiber und weitere Informationen finden Sie unter:
Autres langues de ce document, les pilotes et autres informations, s'il vous plaît visitez:
Altre lingue di questo documento, driver e altre informazioni, si prega di visitare il sito:
http://nec-sbc-service.com
