NEC UX5000 Manual Download

Page: 416 / 588

Customize
Mailbox Options: Message Center: [Message Notification]

398

◆

Chapter 3: Programming

UX Mail Manual

●

(Wait for sound)

This command waits 2 seconds for any constant sound (such as non-standard dial tone), and continues
if sound is detected.

●

(Wait for dial tone)

This command waits for CO dial tone, and then continues.

Default

✔

Indexes 1

entries are

None

[Message Notification]

Call Type

For each

Notification Number

you enter, use this option to specify the type of call the number represents

(Internal, Local, or Long Distance).

●

Internal

calls redial exactly as entered. They are normally 3 or 4 digits long.

●

Local

calls are preceded by the whatever digits or commands are entered in

Customize: Tenant

Options:

. They are normally 5-8 digits long, but also

include:
1+ 800 +XXX+XXXX
1+ 877 + XXX+XXXX
1 + 888 + XXX + XXXX

●

Long Distance

calls are preceded by whatever digits or commands are entered in

Customize: Tenant

Options:

. Long distance calls are normally

longer than 8 digits.

You can override the

Call Type

for a specific

Notification Number

entry, if required. For example, if the

Notification Number

entry is 203 926 5400, and this is a 10-digit local call, you can set

Call Type

Local

(even though it is a 10-digit call). This capability

is not

available to mailbox users entering callout numbers

from the mailbox.

Options

●

Internal

(internal call - see above).

●

Local

(local call - see above).

●

Long Dis.

(long distance call - see above).

Default

✔

Internal

(internal call).

[Message Notification]

Mode

Use this option to specify the type of device the

Notification Number

is dialing. Each device has unique

requirements and capabilities.

●

Normal

Notification is used when the notification destination is a normal voice destination (such as a

cell phone, home office or an internal extension).
- See

for more.

●

Radio Pager

Notification is used when the notification destination is a radio pager.

- See

for more.

●

Digital Pager

Notification is used when the notification destination is a digital (display) pager.

- See

for more.

●

Message Delivery

Notification is used to deliver all of a subscriber’s voice messages to an off-site

location, and then delete them.
- See

for more.

Options

●

Normal

(Normal Notification)

●

Radio Pager

(Radio Pager Notification)

●

Digital Pager

(Digital Pager Notification)

●

M. Deliver

(Message Delivery Notification)

Default

✔

Normal

(Normal Notification)

Summary of Contents for UX5000













































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for UX5000

Reviews:

Related manuals for UX5000

Brands by name

Popular brands

NEC UX5000, Manual

Search results

Summary of Contents for UX5000

Reviews:

Related manuals for UX5000

Brands by name

Popular brands