NEC XN120 Vision Feature Manual Download

Page: 201 / 222

Features

Features Manual

199

Trunk to Trunk transfer restriction.

Program 20-11-14 - Must be set to 0 (Not restricted) to allow an extension to perform Hold and
Transfer of two trunk calls.

Default Setting

Trunk to Trunk transfer is disabled, Program 14-01-13.

Network Disconnect signal is disabled, Program 14-02-12.

Off Premise call forward is disabled, Program 20-11-12.

Trunk to Trunk disconnect timer is set to 1800 Seconds, Program 24-02-07.

DISA conversation (Trunk to Trunk conversation) timer is set to 45 Seconds, Program 25-07-07 & 08.

Route option for DISA class 1 is disabled, Program 20-14-02.

Trunk route for all trunk ports is set to 0 (None), Program 21-03-01.

Trunk to Trunk Transfer restriction is set to ‘not restricted’ for all classes of service, Program
20-11-14.

Programming

14-01-13 : Trunk to Trunk Transfer

14-02-12 : Network Disconnect Signal

20-11-12 : Off Premise Call Forward

20-11-14 : Trunk to Trunk Transfer Restriction

20-14-02 : Route Option for DISA

21-13-01 : Trunk Outgoing Route Access

Trunk to Trunk Disconnect Timer

25-07-07 & 08 : DISA Conversation Timer

Related Features

Hold

Transfer

Call Forward to Abbreviated Dial

Call Forward Off Premise

Trunk to Trunk Forwarding

Operation

Refer to each Related Feature

Summary of Contents for XN120 Vision































































































































































































































Search results

Summary of Contents for XN120 Vision

Reviews:

Related manuals for XN120 Vision

Brands by name

Popular brands

NEC XN120 Vision, Feature Manual

Search results

Summary of Contents for XN120 Vision

Reviews:

Related manuals for XN120 Vision

Brands by name

Popular brands