background image

1

WARNING AND CAUTION

WARNING AND CAUTION

RISK OF ELECTRIC SHOCK

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DO NOT OPEN

CAUTION:  

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

This symbol warns he user that uninsulated voltage within the unit may have
sufficient magnitude to cause electric shock. Therefore, if it is dangerous to make
any kind of contact with any part inside of the unit.

This symbol alerts the user that important literature concerning the operation
and maintenance of this unit has been included. Therefore, it should be read
carefully in order to avoid any problems.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE. ALSO DO NOT USE THIS UNITS POLARIZED PLUG WITH AN EXTENSION CORD
RECEPTACLE O R OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN
FROM OPENING THE CABINET, AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

DOC COMPLIANCE NOTICE

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.

WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed t o provide reasonable protection
against harmful interference when the equipment is operated in a residential environment. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment loss cause harmful interference radio or television reception, which can be determined by
powering the unit on and off, the user is encouraged to try to correct the interference of his or hers
own expense.

Summary of Contents for XV2930

















Reviews: