Nederman 884, Instruction Manual

Hose Reel 884

EN

4 Mounting instruction

See 

Figure 1

.

The reel can be wall-, floor- or ceiling mounted ac-

cording to the pictures. The maximum installation

height above floor level is 4 m. Select a level surface

on which to mount the reel and use the template to

mark the holes. Ensure that suitable fixing bolts are

used and that they are secure. The bolts must stand a

torque force of a minimum of 7600 N.
When choosing the mounting place it should be noti-

fied that the lifetime of the hose can be affected by

chemicals and strong UV- or heat radiation. Weight,

including hose: 28 - 30 kg.

4.1 Hose outlet

See 

Figure 2

 pos. A.

The hose outlet can be rotated and locked in various

positions. Select an angle to ensure a minimum bend-

ing angle for the hose against the outlet rollers.

4.2 Connection to the pipework system

See 

Figure 2

 pos. B.

The reel must be connected to the pipework system

with an inlet hose only, a minimum of 0.5 m. The hose

should go through the ring* which shall be fitted on

the bracket. Check that the hose is not twisted or

strained after connection. A stop valve should be fit-

ted on the pipe system before the hose connection.

4.3 Ratchet mechanism

See 

Figure 3

.

The Hose Reel 884 is delivered with a ratchet mech-

anism that retains the hose in the required outdrawn

position. The ratchet will disengage if the hose is

drawn out a little further and the hose then recoils to

the drum.

WARNING! Risk of personal injury

Do not release the hose until the hose stop

meets the hose outlet.

4.4 Selecting hose

When selecting a hose, see the dimension and work-

ing pressure on the reels identification label.

4.5 Hose fitting

See 

Figure 4

.

1 Install the reel in the intended place.
2 Pull the hose through the outlet of the reel and

fasten the end of the hose onto the swivel. Lay

the hose, fully extended from the reel, on the

floor. See maximum hose length on the identifica-

tion label of the reel.

3 Release the safety latch. Make sure the hose is

under full control without any slack. Do not let go

of the hose before the hose stop meets the hose

outlet.

4 Release the latch mechanism by pulling the hose

slightly in the direction of the arrow. Then let the

hose slowly coil up on to the reel drum.

5 Fit the hose stop at the desired length. See 

Sec-

tion 4.6 Adjustment of spring tension

 item 1.

4.6 Adjustment of spring tension

WARNING! Risk of personal injury

Use protective gloves.

See 

Figure 5

, 

Figure 6

 and 

Figure 7

.

1 Recoil the hose until the hose stop stops against

the outlet. Pull the hose out, to a position where

the ratchet is engaged. Unscrew the hose stop

and the tool connected to the hose.

2 Turn the drum, with all hose wound on: one re-

volution in the direction of the black arrow when

increasing the spring tension, one revolution in

the direction of the grey arrow when decreasing

the spring tension.

3 Refit the hose stop and the tool.
4 Check that the required length of the hose can be

pulled out without stretching the spring to its lim-

it. Do not use higher spring tension than neces-

sary.

5 Maintenance

Following maintenance is recommended regularly or

at least once a year. Also, see 

Figure 6

.

A Check the spring function by testing if the hose re-

coils properly.

B Check that swivel and hose couplings do not leak.

Change the seal if required. Clean the swivel and

couplings.

C Check that the hose is intact. Clean the hose if oily

or dirty.

D Check the ratchet mechanism.
E Check the mounting of the reel on the wall or ceil-

ing.

6 Repair instructions

WARNING! Risk of personal injury

Before starting any operation in the reel:
• Turn off the supply of air/water/oil/grease.
• Engage the safety catch before changing the

hose or swivel.

• Before starting other operations, release the

spring tension by removing the hose stop and

allow the hose to recoil completely.

See 

Figure 7

.

12