background image

FlexPAK

4.2.37 DuctIsoDamp

DuctIsoDamp is used in ATEX applications. This function enables the Duct Isolation Damper sequence function.
DuctIsoDamp is used to ensure that the safety damper, Duct Insulation Damper Safety Damper, does not delib-

erately close during filter cleaning.
When enabled, settings must be made by the Parameters (IsoVDly and FCDely).
For more information, see 

Section 8.2 Tuning Duct Isolation Damper sequence

.

ESC

OK

DuctIsoDamp    1/1 

Switch = Off

Switch = Off Default setting

4.2.38 BLI-Alarm

Menu for setting the delay time for the Bin Level Indicator Alarm message. When the BLI signal disappears, the

BLI-Alarm timer is activated. When the timer elapses, the Alarm message “Alarm! Dustbin Full” appears and the

vacuum unit is stopped.

ESC

OK

BLI-Alarm

 

1/1 

T

= 30:00m

Ta  = 00:00m

T=30:00m: Time before Alarm! Dustbin Full message is activated. The de-

fault is 30 minutes.
Ta=00:00: Elapsed time since the BLI-sensor was activated.

4.2.39 MFDPS-Al

Menu for setting the Main Filter Differential Pressure Sensor Alarm (MFDPS-Al) delay timer. When the Main

Filter pressure sensor monitoring detect High dP across Main Filter, MFDPS-Al is activated. When the delay

timer has expired, the “Alarm! Main Filter Clogged” message is activated. See 

Section 3.2.2 Warning! Main Filter

Clogged

.

When the timer has expired, the unit stops.

ESC

OK

MFDPS-Al

 

1/1 

T

= 20:00m

Ta  = 00:00m

T=30:00m Time before MFDPS-Al is activated. The default is 30 minutes.
Ta=00:00 The elapsed time since High dP across Main Filter was detected.

4.2.40 DPFClean

Menu for activation and deactivation of DPFClean. When activated, this function causes the Main Filter Differ-

ential Pressure to activate cleaning of the main filter.
When the Main Filter pressure sensor monitoring detect High dP across Main Filter, it activates MFDPS-FC,

which delays the start of the cleaning cycle. The delay is designed to filter away a temporarily high differential

pressure over the main filter. See 

Section 4.2.11 MFDPS-FC

.

ESC

OK

DPFClean      1/1 

Switch = Off

Switch=Off is the default setting; DPFClean is deactivated.
To activate DPFClean, set Switch=On.

39

Summary of Contents for FlexPAK
























































Reviews: