background image

L-PAK 150/250 Standard

EN

14

6.2.3 

SSR_Time

Menu for setting the SSR timer. The SSR timer is for the amount of time before the unit 

goes from Idling mode to Standby mode when the pilot signal disappears.

ESC

OK

SSR_Time

1/1 

T = 12:00m

Ta  = 00:00

T = 12:00m: Time before SSR_Time is activated. The default setting is 12 

minutes. The minimum setting is 5 minutes.
Ta = 00:00: The elapsed time since the pilot signal disappeared.

6.2.4 

DIR_Time

Menu for setting the DIR timer. The DIR timer is the amount of time before the unit goes 

from Running mode into Idling mode when the pilot signal disappears.

ESC

OK

DIRTmr

1/1 

T = 10:00s

Ta  = 00:00

T = 10:00s: Time before DIR_Time is activated. The default setting is 10 

seconds The minimum setting is 5 seconds.
Ta = 00:00: The elapsed time since the pilot signal disappeared.

6.2.5 

FCTmr

Menu for activating and setting time between timer controlled filter cleaning.

ESC

OK

FCTmr

 

1/1 

Stat = ON

TH

= 01:00s

TL

= 60:00m

Stat =On Filter Cleaning timer activated Default is On.
TH=01:00s: Do not change the default setting of 1 second.
TL=60:00m: Time between automatic filter cleanings. The default setting 

is 60 minutes.
Ta=00:00: The elapsed time since the last automatic cleaning was 

activated. 

6.2.6 

Clean cycle 

Menu for setting the opening and closing times for the “FCV” Filter Cleaning Valve.
FCV cleaning cycle repeats X times depend on value of parameter ‘On’.
This function is always active when filter cleaning takes place. 

ESC

OK

Clean Cyc   

1/1 

Tch  = 05:00s

Tpu  = 01:00s

On  = 1

Cnt  =0

Tch = Vacuum Building time (Charge Time): Default is 5 seconds.
Tpu = Clean pulse time. Default 1 second.
On = Number of cleaning pulses.
Cnt = 0: Elapsed cleaning pulses.

NOTE! 

For the parameter ‘On’, the minimum value = 1.

NOTE! 

If On is set to 0, No filter cleaning is performed.

Time duration for a cleaning cycle below:

Example: 1 Cleaning pulse 

On=1, Tch=5, Tpu=1 → On * (Tch + Tpu) = 1*(5+1) =6s where Tch=05:00s and Tpu=01:00s.
The default time for a complete cleaning cycle is 6 seconds.

Summary of Contents for L-PAK Series


















Reviews: