Operating the appliance
en
13
1
Operating the appliance
Operating the appliance
You have already learnt about the controls and how
they work. Now we will explain how to set your
appliance. You will learn about what happens when you
switch the appliance on and off, and how to select the
operating mode.
Switching the appliance on and off
Touch the
#
touch button to switch the appliance on or
off.
After switching off the appliance, on the display you can
see if the residual heat in the cooking compartment is
high or low.
Notes
■
Certain displays and notes, such as the residual heat
in the cooking compartment, remain visible on the
display even when the appliance is switched off.
■
After an appliance operation, the cooling fan runs on
audibly until the cooking compartment has been
cooled as far as possible.
■
Switch off your device when you do not need to use
it. If no settings are applied for a long time, the
appliance switches itself off automatically.
Setting and starting the appliance operation
Example: CircoTherm hot air
‚
at 170 °C
1.
Touch the
#
touch button to switch on the
appliance.
You are taken directly to the
¢
menu for the types of
heating.
2.
Use the
(
or
)
button to select the type of heating.
3.
Use the
&
button to navigate to the next line.
4.
Use the
(
or
)
button to select the temperature.
Note:
Depending on the operating mode, different
settings are available. For each further setting, use
the
&
button to navigate to the next line. Use the
(
or
)
button to select the setting.
5.
Touch the
#
touch button to start the appliance
operation.
The heating bar and run time appear on the display.
Note:
If you would like to go directly to the
0
main
menu after switching on the appliance, you can select
the main menu under "Operation after switching on" in
Default values
The appliance suggests a temperature or setting for
each type of heating. You can accept this value or
change it in the appropriate area.
Heating bar
As soon as a type of heating has started, the heating
bar appears on the display.The heating bar shows the
temperature increase in the cooking compartment.
Run time
When a type of heating has been started, the run time is
displayed. The run time counts upwards during the
operation. You can therefore check how long the
operation has already been running.
Displaying the current temperature
To show the current temperature on the display, press
the
!
touch button.
The current temperature is shown briefly only when
heating up.
Further information
If the
!
touch button lights up, information can be
displayed. Touch the
!
touch button to do this. The
information is displayed for a few seconds.
Changing or cancelling the appliance
operation
Changing the appliance operation
1.
Use the
#
button to stop the operation.
2.
Use the
&
or
%
button to navigate to the line for the
setting that should be changed.
3.
Use the
(
or
)
button to change the setting.
4.
Use the
#
touch button to start the changed
operation.
Notes
■
The cooling fan may continue to run while an
operation is interrupted.
■
After a temperature change, the paused running time
continues to count. After a change in the type of
heating, the running time starts again from zero.
Cancelling the appliance operation
Press and hold the
#
touch button until the appliance
operation is cancelled.
Note:
Operating modes such as the cleaning function
cannot be cancelled.
Display
Meaning
-H-
Residual heat high (above 120 °C)
-h-
Residual heat low (between 60 °C and 120 °C)
&LUFR7KHUPKRWDLU
&
&LUFR7KHUPKRWDLU
&
Summary of Contents for B27CR22 1 Series
