35
3.
Clean the hook-in rack with washing-up liquid and a sponge
or brush.
4.
Align the hook-in rack with the indentation (a) facing
downwards, so that the shelf heights match.
5.
Insert the hook-in rack at the rear as far as it will go and push
to the rear (figure C).
6.
Insert the hook-in rack at the front as far as it will go and push
downwards (figure D).
Faults and repairs
It is not always necessary to call the after-sales service.
Sometimes, you can find a remedy yourself. You will find some
tips for troubleshooting in the following table.
ã=
Risk of electric shock!
■
Work on the appliance electronics may only be performed by
a specialist.
■
Always disconnect the appliance from the power supply
when work is carried out on the electronics. Switch off the
circuit breaker or remove the fuse from your household fuse
box.
D
D
&
'
Problem
Possible cause
Remedial action
Electrical function is faulty (e.g. indicator
lamps do not light up)
Fuse defective
Check fuses in the fuse box and replace if
necessary
Liquid or runny dough runs to one side
Appliance not installed level
Check the appliance installation (see
the Installation instructions)
‹
:
‹‹
flashes in the clock display
There was a power cut
Press the
KJ
clock function button, reset
the clock (see section: Electronic clock)
‹
:
‹‹
flashes on the clock display, "rrr"
appears on the temperature display
The power supply was interrupted while
the appliance was in operation
Press the
KJ
clock function button, reset
the clock (see section: Electronic clock)
The appliance prompts you to descale or
to run the 1st or 2nd rinse
The power supply was interrupted or the
appliance was switched off during the des-
caling process
After you have switched the appliance
back on, repeat the process that was inter-
rupted (e.g. 1st rinse) and then continue
with the descaling process.
"E011" appears in the clock display.
Permanent assignment of a button
Cancel the permanent assignment of the
button and press the
KJ
clock function
button
"EXXX" appears in the clock display,
e.g. E300
Internal fault in the appliance electronics
Press the
KJ
clock function button. If the
message does not go out, pull out the
mains plug and plug it back in again after
approx. 10 seconds
It is not possible to operate the appliance,
"Appliance locked" appears on the text
display,
D
and -
†
- appear on the temper-
ature display.
The appliance has been locked
Deactivate the lock
(see section: Childproof lock)
It is not possible to operate the appliance,
“Appliance permanently locked" appears
on the text display,
D
and
†˜
appear on
the temperature display.
The appliance controls are locked perma-
nently
Deactivate the permanent lock
(see section: Childproof lock)
The appliance does not heat up, the two
dots flash on the clock display
‚‡‹©
appears in the temperature display, for
example
A button combination was actuated
Turn the operating mode selector to the
Û
off position, press and hold the
±
info but-
ton for 3 seconds, then press and hold
the
KJ
clock function button for
4 seconds, then press and hold the
±
info
button again for 3 seconds
Electronically controlled functions are mal-
functioning
Energy surges (e.g. lightning strike)
Reset the function concerned
Once you have switched on an operating
mode,
•
or
œ
appears on the temperature
display, and “Not possible" appears on the
text display
The appliance has not cooled down fully
Wait until the appliance has cooled down,
then switch on the operating mode again
The appliance has switched off automati-
cally. "Safety switch-off" appears in the text
display,
‹
:
‹‹
flashes in the temperature
display
The appliance has switched off to protect
itself from overheating
Turn the operating mode selector back to
the
Û
position
