Steam
en
19
5.
Take out the cover
‚
(Fig.
#
).
Note:
Whether or not there is a cover
‚
depends on
the appliance type.
6.
Fill the water tank with cold water up to the "max."
mark (Fig.
$
).
7.
Put the cover
‚
back into the opening on the water
tank.
8.
Insert the filled water tank (Fig.
%
). Ensure that the
water tank locks into place behind both holders
ƒ
(Fig.
&
).
9.
Slowly slide the control panel downwards and then
push it towards the rear until it is closed completely.
The water tank has been filled. You can start using
operating modes with steam.
Refilling the water tank
Notes
■
Steam-assisted operations continue without adding
steam.
■
If the water tank runs dry during operation with the
Dough proving or Reheat settings, operation is
interrupted. Fill the water tank.
1.
Open the control panel.
2.
Remove and refill the water tank.
3.
Insert the filled water tank and close the control
panel.
After every steam operation
:
Warning – Risk of scalding!
When you open the appliance door, hot steam can
escape. Steam may not be visible, depending on its
temperature. When opening, do not stand too close to
the appliance. Open the appliance door carefully. Keep
children away.
:
Warning – Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
Caution!
Enamel damage: Do not start any operations when
there is water on the cooking compartment floor. Before
operation, wipe away the water from the cooking
compartment floor.
The remaining water is pumped back into the water
tank after every operation with steam. Then empty and
dry the water tank. Moisture remains in the cooking
compartment. To dry the cooking compartment, you
can either use the "Drying
ª
" operating mode or dry the
cooking compartment by hand.
Notes
■
Once the appliance has been switched off, the
”
touch button remains lit for a little longer to remind
you to empty the water tank.
■
Remove limescale marks with a cloth soaked in
vinegar, then wipe with clean water and dry with a
soft cloth.
Emptying the water tank
Caution!
■
Do not dry the water tank in the hot cooking
compartment. This will damage the water tank.
■
Do not clean the water tank in the dishwasher. This
will damage the water tank.
1.
Open the control panel.
2.
Remove water tank.
3.
Carefully remove the lid of the water tank.
4.
Empty the water tank, clean it with detergent and
then rinse it thoroughly with clean water.
5.
Dry all parts with a soft cloth.
6.
Rub the seal on the lid until dry.
7.
Leave to dry with the lid open.
8.
Place the lid on the water tank and push it down.
9.
Insert the water tank and close the control panel.
Starting drying
To dry the cooking compartment, it is heated up so that
the moisture in the cooking compartment evaporates.
You will then need to open the appliance door to allow
the steam to escape from the cooking compartment.
Caution!
Enamel damage: Do not start any operations when
there is water on the cooking compartment floor. Before
operation, wipe away the water from the cooking
compartment floor.
1.
Allow the appliance to cool down.
2.
Remove the worst of the food remnants from the
cooking compartment immediately and use a
sponge to wipe away moisture from the cooking
compartment floor.
3.
If necessary, touch the
#
touch button to switch the
appliance on.
4.
Touch the
0
field to display the operating modes.
5.
On the touch display, swipe to the left or right to
select "Dry
ª
".
6.
Touch the line at the bottom.
The duration will be displayed. It cannot be changed.
7.
Touch the line at the bottom.
D
E
E
I
Summary of Contents for B58VT68H0
