NEFF C1.KS61N0, Installation Instructions Manual

2 

en

Safety instructions

R

Please read and pay particular attention to the safety information in the instruction manual.

W

Danger of electric shock!

Connect and operate the appliance only according to the type plate specifications. To avoid  potential 

hazards, repairs must only be carried out by our customer service personnel. 

If the power cord of this appliance is damaged, it must be replaced with a special connection cord, 

which is available from our after-sales service. Should a fault occur, pull the plug or disconnect from 

the mains immediately. 

Only an appliance which has been correctly installed according to these installation instructions can 

be used safely. Attach loose furniture to the wall with a conventional bracket.

The appliance contains permanent magnets that may influence electronic implants such as 

 pacemakers or insulin pumps. Persons wearing electronic implants must maintain a minimum 

distance of 10 cm from the front of the appliance and from the following parts upon removal: milk 

container, milk system, water tank and brewing unit.

Included in delivery

a 

Fully automatic coffee machine

b 

Instruction manual

c 

Filter instructions

d 

Installation instructions 

e 

Connecting cable

f 

Assembly bracket

g 

Spacer

h 

5 fastening screws (silver)

i 

2 fastening screws (long/black)

j 

2 fastening screws (short/black)

k 

1 sleeve (black)

l 

2 sleeves (white)

m 

Quick reference guide 

n 

Measuring spoon 

o 

Water hardness testing strip

p 

Milk tube (set) 

q 

Milk container

r 

Suction pipe 

Installing the appliance

Make sure there is adequate aeration. To do this, remove the 

rear panel or cut out an opening of 500 x 400 mm. There must 

be a gap of at least 35 mm between the wall and base of the 

unit or the rear panel of the unit situated above. The ventilation 

slots and intake openings must not be covered. Also follow the 

installation instructions for the appliance situated above or below. 

If installing the appliance above a warming drawer, the height of 

the recess must be 590 mm. If the appliance is installed directly 

under a décor panel, ensure that there is a ventilation slot of at 

least 200 cm². The ideal installation height for the fully automatic 

coffee machine, measured from the floor to the lower edge of the 

appliance, is 950 mm.

1 

Unpack all the parts and check for any damage in transit. 

Do not operate a damaged appliance.

2 

Take note of the installation dimensions of the particular 

model.

Important

: 2 opening angles can be selected for the door.

Depending on the opening angle required, the mounting distance 

to the wall should be observed before installation if it is on the left 

side.

■

 Opening angle approx. 110° (as delivered) 

= mounting distance to the wall at least 350 mm on the left.

■

Opening angle approx. 92° (requires special accessory) 

= mounting distance to the wall at least 100 mm on the left. 

For this purpose, replace the two limits on the upper and lower 

hinges with special accessory no. 00636455.

3 

Remove the installation template on the back of the installation 

instructions. Place the installation template at the front edge 

of the unit and screw on the assembly bracket 

f

 as shown 

with two fastening screws 

h

. The assembly bracket must be 

positioned at the base of the unit and the wall such that no 

gap is present.

4 

Set the mains switch 

U

 to 

h

. Plug the connecting cable 

e

into the socket first and then into the appliance (clicks into 

place). It must not be trapped or kinked. Put the appliance to 

be plugged in just on to the edge of the unit.

Important

: The distance between the appliance and the back wall 

must be at least 100 mm.

5 

Push the appliance into the unit until it clicks into place. Check 

that the appliance is in the middle. If necessary, align the 

appliance. To do so, pull the appliance out a little, remove the 

appropriate spacers

 g

 and attach to the left side (top and 

bottom). Push the appliance into the unit until it clicks into 

place.

6 

Take hold of the appliance door on the right next to the outlet 

and open. Remove the drip tray 

Y

. Pull the cover 

X

 on the 

bottom left-hand side forwards and remove. Pull out the 

accessories drawer 

Z

 and put to one side.

7 

First, screw on the appliance as shown using 2 of each of 

the fastening screws 

h

 and 

i

 as well as 2 sleeves 

l

. Then 

screw tight at the top right of the unit using 1 fastening screw 

h

 and sleeve 

k

.

8  Only for the expert

In very few cases, the door of the fitted fully automatic 

machine can jam due to a warpage in the built-in units. The 

door can be adjusted. To do this adjust the hinges at the top 

and the bottom.

I. 

Adjust the depth of the door by turning the screws 

V

.

II. 

Remove the hinge dampers at the top and bottom of the 

hinges. Turn the screws 

W

 to adjust the inclination and the 

horizontal position of the doors. 

III. 

Re-fit the hinge dampers.

9 

Insert the cover 

X

 and fix with the two black fastening 

screws 

j

.

10 

Replace the drip tray 

Y

 and accessories drawer 

Z

 and close 

the appliance door.