background image

7

Cleaning and care

Isolate the extractor hood by pulling out
the mains plug or switching off the fuse.

Do not clean the extractor hood with

abrasive sponges or with cleaning agents
which contain sand, soda, acid or chlorine!

Clean the extractor hood with a hot soap
solution or a mild window cleaner.

Do not scrape off dried-on dirt but wipe
off with a damp cloth.

When cleaning the grease filters, remove
grease deposits from accessible parts of
the housing. This prevents the risk of fire
and ensures that the extractor hood
continues operating at maximum 
efficiency.

Note: 

Do not use alcohol (spirit) on 

plastic surfaces, as dull marks may
appear.

Caution: 

Ensure that the kitchen is ade-

quately ventilated. Avoid naked flames!

Clean the operating buttons with a mild

soapy solution and a soft, damp cloth only.
Do not use stainless-steel cleaner to clean
the operating buttons.

Stainless steel surfaces:

Use a mild non-abrasive stainless steel
cleaner.

Clean the surface in the same direction
as it has been ground and polished.

We recommend our stainless steel 
cleaner no. 461731.
See enclosed service booklet for order
address.

Aluminium and plastic surfaces:

Do not use dry cloths.

Use a mild window cleaning agent.

Do not use aggressive, acidic or caustic
cleaners.

Observe the warranty regulations in the
enclosed service booklet.

4.

Re-insert the bulb ring.

5.

Plug the appliance into the mains or
switch it on at the fuse box.

Note: I

f the light does not function, check

that the bulbs have been inserted correctly.

Replacing the light bulbs

1.

Switch off the extractor hood and pull
out the mains plug or switch off the
electricity supply at the fuse box.

When switched on, the halogen bulbs

become very hot. Even for some time after
the bulbs have been switched off there is
still a risk of burns.

2.

Remove the bulb ring with a screwdriver
or similar tool.

3.

Replace the halogen light bulb 
(conventional halogen bulb, 12 Volt,
max. 20 Watt, G4 cap).

Caution:

Refer for plug-in lampholder.

Take hold of the bulb with a clean cloth.

Summary of Contents for D8662N0GB

















Reviews: