background image

  Cleaning and maintenance   

en

7

2

Cleaning and maintenance

Cleaning 

and maint

enance

:

Warning

Risk of burns!

The appliance will become hot during operation, 

especially near the bulbs. Allow the appliance to cool 

down before cleaning.

:

Warning

Risk of electric shock!

Penetrating moisture may result in an electric shock. 

Clean the appliance using a damp cloth only. Before 

cleaning, pull out the mains plug or switch off the circuit 

breaker in the fuse box.

:

Warning

Risk of electric shock!

Do not use any high-pressure cleaners or steam 

cleaners, which can result in an electric shock.

:

Warning

Risk of injury!

Components inside the appliance may have sharp 

edges. Wear protective gloves.

Cleaning agents

To ensure that the different surfaces are not damaged 

by using the wrong cleaning agent, observe the 

information in the table. Do not use any of the following:

Harsh or abrasive cleaning agents,

Cleaning agents with a high alcohol content,

Hard scouring pads or cleaning sponges,

High-pressure cleaners or steam cleaners.

Wash new sponge cloths thoroughly before use.
Follow all instructions and warnings included with the 

cleaning agents.

Cleaning the metal mesh grease filters

These instructions apply to several appliance variants. It 

is possible that individual features are described which 

do not apply to your appliance.

:

Warning

Risk of fire!

Grease deposits in the grease filter may catch fire.

Clean the grease filter at least every 2 months. 

Never operate the appliance without the grease filter.

Notes

Do not use any aggressive, acidic or alkaline 

cleaning agents.

When cleaning the metal mesh grease filters, also 

clean the holder for the metal mesh grease filters in 

the appliance using a damp cloth.

The metal mesh grease filters can be cleaned in the 

dishwasher or by hand.

By hand:

Note: 

You can use a special grease solvent for 

stubborn dirt. It can be ordered via the Online Shop.

Soak the metal mesh grease filters in a hot soapy 

solution. 

Clean the filters with a brush and then rinse them 

thoroughly.

Leave the metal mesh grease filters to drain.

In the dishwasher:

Note: 

If the metal mesh grease filters are cleaned in the 

dishwasher, slight discolouration may occur. This has 

no effect on the function of the metal mesh grease 

filters.

Do not clean heavily soiled metal mesh grease filters 

together with utensils.

Place the metal mesh grease filters loosely in the 

dishwasher. The metal mesh grease filters must not 

be wedged in.

Area

Cleaning agent

Stainless steel

Hot soapy water: 

Clean with a dish cloth and then dry with a 

soft cloth.
Clean stainless steel surfaces in the grind 

direction only.
Special stainless steel cleaning products are 

available from our after-sales service or from 

specialist retailers. Apply a very thin layer of 

the cleaning product with a soft cloth.

Painted surfaces

Hot soapy water: 

Clean using a damp dish cloth and dry with a 

soft cloth/towel.
Do not use any stainless steel cleaners.

Aluminium and plastic Glass cleaner: 

Clean with a soft cloth.

Glass

Glass cleaner: 

Clean with a soft cloth. Do not use a glass 

scraper.

Controls

Hot soapy water: 

Clean using a damp dish cloth and dry with a 

soft cloth/towel.
Risk of electric shock caused by penetrating 

moisture.
Risk of damage to the electronics from pene-

trating moisture. Never clean operating con-

trols with a wet cloth.
Do not use any stainless steel cleaners.

Area

Cleaning agent

Summary of Contents for DFL063W50

















Reviews: