34
Accessing the basic settings
The hob should be turned off.
1.
Switch on the hob.
2.
Within the next 10 seconds, press the
‚
symbol for
4 seconds.
In the display
™
and
‚
light up alternatively and
‹
as a
default setting.
3.
Press the
‚
symbol several times until the required function
appears.
4.
Next select the required setting using the
+
and
-
symbols.
5.
Press the
‚
symbol again for more than 4 seconds.
The settings should be correctly saved.
Quit
To leave the basic settings, turn off the hob at the main switch.
Care and cleaning
The advice and warnings contained in this section aim to guide
you in cleaning and maintaining the hob, so that it is kept in the
best possible condition
Hob
Cleaning
Clean the hob after each use. This prevents food remains left
on the surface from burning. Wait until the hob is cool enough
before attempting to clean it.
Only use cleaning products specifically designed for hobs.
Follow the instructions provided on the packaging.
Do not use:
■
Undiluted washing-up liquid
■
Dishwasher detergent
■
Abrasive products
■
Corrosive products such as oven sprays or stain removers
■
Sponges that may scratch
■
High-pressure or steam cleaners
The best way to remove stubborn stains is to use a glass
scraper. Follow the manufacturer's instructions.
Suitable glass scrapers can be obtained through the Technical
Assistance Service or from our online shop.
Hob frame
In order to avoid damage to the hob frame, follow the
indications below:
■
Use only slightly soapy hot water
■
Do not use sharp or abrasive products
■
Do not use a glass scraper
Fixing malfunctions
Malfunctions are usually due to small details. Before calling the
Technical Assistance Service you should bear in mind the
following advice and warnings.
Indicator
Malfunction
Solution
none
The electric power supply has been cut off.
Use other electrical appliances to check whether there
has been a power cut.
The appliance has not been correctly con-
nected following the connection diagram.
Check that the appliance has been connected cor-
rectly according to the connection diagram.
Electronic system malfunction.
If none of the above checks resolve the malfunction,
contact the Technical Assistance Service.
The indicators flash
The control panel is damp or an object is rest-
ing on it.
Dry the control panel area or remove the object.
The indicator
-
flashes on
the hotplate indicators
A fault has occurred in the electronic system. Briefly cover the control panel with your hand to con-
firm the malfunction.
* If the warning persists call the Technical Assistance Service.
Do not rest hot pans on the control panel.
Summary of Contents for T B10 Series
