Twist-Pad with Twist knob
en
35
j
Twist-Pad with Twist knob
Twist-Pad with Twist knob
The twistpad is the area in which you can use the twist
knob to select the hotplates and set heat settings. The
twist knob automatically centres itself in the twistpad
area.
The twist knob is magnetic and is placed on the
twistpad. Tapping the twist knob where there is a
marking activates the relevant hotplate. Turning the
twist knob selects the heat setting.
Note:
Always keep the twist knob clean. Soiling may
impair its function.
Removing twist knob
You can remove the touch knob. This makes cleaning
easier.
You can also remove the twist knob while the hotplate
is on. The wipe protection function is activated and the
hob switches off after 35 seconds.
Notes
■
The main switch is excluded from the wipe
protection function. You can switch off the cooktop
at any time.
■
If you mount the twist knob again and then turn it, the
wipe protection function will be switched off.
:
Warning – Risk of fire!
If you place a metallic object onto the twistpad, the
cooktop may continue to heat up. Always switch off the
cooktop using the main switch for this reason.
Storing the twist knob
The twist knob contains a strong magnet. Keep the twist
knob away from magnetic data carriers, such as video
cassettes, diskettes, credit cards or cards with
magnetic strips. Otherwise they may be damaged
beyond repair. They can also cause interference in
television sets and monitors.
:
Warning – Hazard due to magnetism!
For wearers of electronic implants, e.g. pacemakers or
insulin pumps. Implants may be affected by magnetic
fields. You should therefore never carry the twist knob in
a pocket. They must be kept at least 10 cm from
pacemakers.
Note:
The twist knob is magnetic. Metal particles which
stick to the underside can scratch the ceramic hob.
Always wipe the twist knob thoroughly.
Operation without the twist knob
If you have mislaid the twist knob, you can also operate
the hob without it:
1.
Switch on the hob using the main switch.
2.
Touch the
œ
symbol and
U
at the same time for 4
seconds. An audible signal sounds.
3.
Touch the
U
symbol repeatedly until the display for
the desired hotplate lights up.
4.
Press the
œ
(-) and (+)
x
buttons to select the heat
setting required.
The hotplate is switched on.
Note:
You can place the twist knob back on the
twistpad at any time.
1
Operating the appliance
Operating the appliance
In this section, you can find out how to set the
hotplates. The table shows heat settings and cooking
times for various meals.
Switching the hob on and off
The main switch is used to switch the hob on and off.
Switching on the appliance
Touch the
#
symbol. A signal sounds. The
A
display
above the main switch lights up. The control displays
and the heat setting displays
‹
light up. The hob is
ready for use.
Switching off the appliance
Touch the
#
symbol until the
A
display above the main
switch and the displays goes out. All hotplates are
switched off. The residual heat indicator remains on
until the hotplates have cooled down sufficiently.
Notes
■
The hob will switch itself off automatically once all
hotplates have been switched off for a while (10-
60 seconds).
■
The settings remain stored for 4 seconds after the
hob has been switched off. If you switch it on again
during this time, the hob will operate using the
previously stored settings.
Setting a hotplate
Use the twist knob to set the desired cooking time.
Heat setting 1 = lowest setting
Heat setting 9 = highest setting
There is an intermediate setting between each heat
setting. This is identified by a dot.
Set the heat setting
The hob must be switched on.
1.
Select the hotplate. To do this, touch the twist knob
in the appropriate area for the required hotplate.
