background image

6

1. Remove the Bolts on the Support Post and reposition to move the guide

rollers, if needed, for the desired mounting location (wall, floor or ceiling).

2. Replace the Bolts and tighten.

MOUNTING REEL

1. Choose a mounting location that is free of electrical wiring or other

obstructions, and is sturdy enough to support the weight of the Reel and

hose as well as the force used to extend and retract it.

2. Make a paper template from the mounting plate of the Reel. Mark the

center of the bolt holes in the desired mounting location.

3. Check for hidden wiring, then, drill holes to accommodate 1/2” bolts

(not included).

4. Mount the Reel and secure in place with four bolts.

OPERATION

ADJUST THE SPRING TENSION

1. Pull out approximately six feet of Hose.

2. Remove the Hose Stopper from the Hose and slide the Hose out of

the Roller Guide so the Hose is hanging loose.

a. To increase tension, wrap the loose hose one time around the

Reel Drum.

b. To decrease tension, unwrap the hose one time from the drum.

3. Run the hose back through the guide and re-attach the hose stopper.

4. Pull the Hose out several feet to check the tension.

GENERAL OPERATING INSTRUCTIONS

1. Check the Wheel operation by slowly pulling the Hose out. You should

hear a clicking noise.

2. To lock the Hose, pull it out a minimum of 1/2 revolution and it will stay

locked after the first, second, or third click.

3. To unlock, slowly pull until the clicking stops, and let it retract until the

Hose Stopper hits the Hose Guide.

CAUTION!

Hold on to the Hose while it is rewinding, to avoid damage to the

Hose Reel.

4. Attach a coupler (sold separately) to your air compressor hose and

apply thread seal tape to the Inlet fitting on the Reel. Connect the

coupler to the Inlet fitting.

5. Connect your air tool to the other end of the Hose using another coupler

and thread seal tape.

6. Follow all instructions from the air tool and compressor for set up and

use.

7. When finished using the Hose, disconnect the air tool and retract the

hose. Wipe the Hose Reel clean with a dry cloth.

Summary of Contents for CT1057









Reviews: