background image

3

CONDITIONS.

We recommend the machine is not used during winds. This may

affect the spreading pattern.

DRESS PROPERLY.

Do not wear loose clothing, gloves, scarfs, neckties

or jewellery (rings, wrist watches), which can be caught in moving parts.

DO NOT OVERREACH.

Keep proper footing and balance at all times

when using the machine. Never stand on the machine. Serious injury could occur
if the machine is tipped or if the moving parts are unintentionally contacted. Do
not store anything above or near the machine, where anyone might stand on the
machine to reach them.

AVOID INJURY FROM UNEXPECTED ACCIDENT.

Keep hands & feet out of the

way of all moving parts. Do not place any part of your body or any tool e.g. in
moving parts of the machine during operation.

DO NOT FORCE TOOL.

Always work within the rated capacity. Do not operate

for a purpose for which it was not intended.

MAINTAIN YOUR MACHINE WITH CARE.

Clean the machine immediately after

use. Keep the machine clean to ensure it operates to its full & safest
performance. When maintaining this machine, only the manufacturer’s original
replacement parts should be used.

PROTECT THE ENVIRONMENT.

Take left over materials to an authorised

collection point or follow the stipulations in the country where the machine is
used. Do not discharge into drains, soil or water.

STORE IDLE EQUIPMENT.

When not in use, the machine should be stored in a

dry location. Keep the machine away from children and others not qualified to
use it.

OPERATION SPEED.

Do not exceed 6 mph, to avoid personal injury and/or

equipment damage.

TYRE INFLATION.

WARNING! Over-inflated tyres can explode and cause

serious injury. Avoid injury by NEVER over inflating tyres beyond the maximum
pressure printed on the side of the tyre wall. ALWAYS use FOOT or HAND pump
inflation devices.
This is a garden/domestic product, therefore extended use over abrasive
surfaces (e.g. concrete, tarmac etc.) could cause premature wear on the tyres.

Summary of Contents for CT2205

















Reviews: