background image

2

1. SPECIFICATIONS

Capacity: 175LB
Spread Width: 4"/1M
Pneumatic Tyre: 10"
Coverage: 40000 Sq/ft
Spikes: 12 spike wheels, 7" dia.
Adjustable flow control lever with stop feature.
Works with lawn/garden tractors and ATVs.

2. GENERAL SAFETY INSTRUCTIONS

Warning: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment. Read all instructions
before using this tool!

STAY ALERT.

Do not operate the machine while under the influence of drugs,

alcohol, or any medication that could affect your ability to use it properly. Do not
use this machine when you are tired or distracted from the job at hand. Be aware
of what you are doing at all times. Use common sense.

USERS.

Do not at any time carry passengers sit or stand on the machine. Do not

allow children to play on, stand upon or climb in the machine. Never allow
children or people unfamiliar with these instructions to use the machine.
Local regulations can restrict the age of the operator.

AVOID DANGEROUS CONDITIONS.

Make sure there is adequate surrounding

workspace. Cluttered areas invite injuries. Keep your work area clean with
sufficient light. Keep the area around the machine clear of obstructions, grease,
oil, rubbish & other debris which could cause persons to fall onto moving
parts.

KEEP BYSTANDERS AND CHILDREN AWAY.

Keep unauthorised persons a

safe distance away from the machine. If approached, stop the machine
immediately. Do not allow children to handle, climb on or use the machine. Keep

Summary of Contents for CT2214





















Reviews: