background image

e.g., at a special collecting point or dump. 
If your device should become useless somewhere in the future or you do not need it 
any  longer,  do  not  dispose  of  the  device  together  with  your  domestic  refuse,  but 
dispose  of  it  in  an  environmentally  friendly  manner.  Thoroughly  empty  the 
oil/lubricant and fuel tanks and dispose of the remainders at a special collecting point 
or dump. Please also dispose of the device itself at an according collecting/recycling 
point.  By  doing  so,  plastic  and  metal  parts  can  be  separated  and  recycled. 
Information concerning the disposal of materials and devices are available from your 
local administration. 

 

13. Troubleshooting guide 

PROBLEM                                    CAUSE                                              REMEDY 

1) Starting failure               

– Check fuel for water            – Replace with proper fuel. 

or substandard mixture. 

                                                                             

– Remove and dry the   

                   

– Check for engine flooding.    spark plug. 

                                                                 

– Then pull the starter   

                   

– Check spark ignition.              again with no choke. 

 
                                                                                               

– Replace with a new plug. 

 

2) Lack of power/Poor       

– Check fuel for water or      – Replace with proper fuel. 

acceleration/                            substandard mixture. 
Rough idling                       

– Check air filter and fuel      – Clean. 

filter for clogging. 

                                                                                                 

– Check carburetor for          – Readjust speed needles. 

inadequate adjustment. 

 
 
3) Oil does not                   

– Check oil for substandard    – Replace. 

come out                                quality. 
 

– Check oil passage and          – Clean. 

ports for clogging. 
 

 
If the unit seems to need further service, please consult with an authorized service 
shop in your area. 
 
 
 

Summary of Contents for CT2298









































Reviews: