background image

 

- 11 - 

 

 
 
 

WARNING 

Before using the push sweeper, review the instructions below and safety information.    Failure to 
follow these instructions may result in property damage or injury to the operator or bystanders.

 

 
 

USING YOUR SWEEPER 

 

1.  Always instruct other users before allowing them to operate the sweeper. 
2.  Do not allow anyone to operate the sweeper without proper instructions. 
3.  Do not at any time carry passengers sit or stand on the sweeper.   
4.  Do not permit children to operate sweeper.

 

5.  Do not push sweeper too close to a fire, the hopper and the brushes will burn. 
6.  Do not exceed the maximum capacity of the hopper 7 Cu. Ft.

 

7.  Use caution when operating the sweeper on rough terrain, ditches and hillsides to prevent tipping. 
8.  This sweeper is not meant for street or highway use. Watch for traffic when sweeping near road ways

 

9.  Keep all nuts, bolts and screws tight to be sure the equipment is safe to operate. 
10. Sweeper should be inspected for damage after striking a foreign object. 
11. 

Replace or repair damaged or worn parts immediately 

before operate the equipment. 

12. Follow all maintenance instructions outlined in this Manual.

 

 
 

BRUSH HEIGHT ADJUSTMENT

 

 

Adjust your sweeper brushes for the best results, loosen the hand knob and slide the height adjustment 
tube down to raise the brushes or up to lower the brushes. Make sure the brushes are no more than ½” 
down into the grass. 
 

 
 
 
 
 
 
 
 
 
 
 
NOTE: Always mow the grass to an even height before sweeping. 

 

 

DUMPING HOPPER BAG 

 
To dump hopper bag, tip the sweeper forward allowing the material to fall out or take the hopper bag off of 
the frame and sweeper to dump. 
 
Always dump hopper after each use. Damp or wet grass and leaves will cause damage to hopper if stored 
for an extended period of time. 
 

 

CAUTION 

DO NOT

 dump or unload the sweeper too close to a fire as the brushes and hopper bag can be destroyed 

by excessive heat or flame. 
 

Operation Instructions

Summary of Contents for CT2200


















Reviews: