background image

 

Page | 7 

 

P: 419.542.7751    F: 419.542.6690   800.782.761   nemcofoodequip.com 

 

 

 

49234A 

 

Timer Mode 

 

The timer function allows you to set a timer from 1 second, up to 719 minutes.  The 
timer resets to 719 minutes every time the power is turned off/on.   The timer always 
runs in the background, so if the unit runs continuously for 12 hours (719 minutes), the 
timer will run out and the unit will turn off.   To reset, turn the power off/on, or 
manually set the timer. 

Setting the Timer 

 

With the unit powered on and in the Ready state (display shows a steady ‘00’), 
press the ‘TMR’ button.  The display will show ‘0719’.   

 

To change the timer setting, press the ‘MIN/SEC’ button.  The display will flash 
‘719’. 

 

Turn the knob to adjust the number of minutes.  Turning the knob to the left will 
reduce the number of minutes.  If you turn the knob to the right past 719, the 
display will go to ’00.59’ or 59 seconds.  Keep turning to the right to increase the 
minutes. 

 

If you want to set seconds, for instance 3 minutes and 30 seconds, turn the knob 
until the display shows ‘03.59’ minutes.  Then press the ‘MIN/SEC’ button again.  
The ‘seconds’ field will flash.  Use the knob to adjust the seconds to 30.  The 
display will show ‘03.30’ 

 

When the time is set to what you want, press the ‘Start/Stop’ button.  The power 
will come on and the timer will count down.  When the timer counts down to 0, 
the unit will stop heating. 

 

While the unit is heating, the display will alternate between the timer and the 
power setting.  You can always adjust the power setting while the display is 
showing the power level. 

 

If you press the TMR button while the unit is heating, the display will stop 
alternating between the timer and the power level.  The timer will continue to 
run.  Pressing the TMR button again will resume alternating the display. 

 

While the unit is heating, the timer display decimal points will flash. 

 

Once the timer counts down to zero, pressing the ‘Start/Stop’ button will restart 
the cycle at the time that you set previously.  Turning the unit off/on using the 
‘Power’ Button will reset the timer to 719 minutes. 

 

Summary of Contents for 9101A














Reviews: