4
do
danych przez użytkownika końcowego lub przeprowadzonych przez
niego późniejszych działań
.
Nazwisko i adres osoby mającej miejsce zamieszkania lub siedzibę w
UE upoważnionej do przygotowania dokumentacji technicznej:
Podpisano w imieniu:
Grupa Topex Sp. Z o.o. Sp.k.
Ul. Pograniczna 2/4
02-285 Warszawa
Paweł Kowalski
Pełnomocnik ds. jakości firmy GRUPA TOPEX
Warszawa, 2022-07-28
EN
TRANSLATION (USER) MANUAL
Tyre fitting machine : 10-606
NOTE: BEFORE USING THE EQUIPMENT, PLEASE READ THIS
MANUAL CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
PERSONS WHO HAVE NOT READ THE INSTRUCTIONS SHOULD
NOT CARRY OUT ASSEMBLY, ADJUSTMENT OR OPERATION OF
THE EQUIPMENT.
SPECIFIC SAFETY PROVISIONS
NOTE!
Read the operating instructions carefully, follow the warnings and safety
conditions contained therein. The appliance has been designed for safe
operation. Nevertheless: installation, maintenance and operation of the
appliance can be hazardous. Following the following procedures will
reduce the risk of fire, electric shock, personal injury and will reduce the
installation time of the appliance
SAFETY RULES
•
The appliance may only be operated by persons who have been
trained to do so and who have read these instructions.
•
Use the personal protective equipment specified in the
instructions, eye protection, hand protection.
•
Care should be taken to ensure that the work area is tidy and does
not pose a hazard to the person operating the assembler.
•
The assembler may only be used in the manner for which it has
been designed.
•
Do not modify the assembler yourself.
PICTOGRAMS AND WARNINGS
1.
WARNING Read the operating instructions
2. Wear personal protective equipment, safety goggles
3. Wear protective gloves
4. Keep children away from the tool
5. NOTE! Requires assembly
6. Recycling
DESCRIPTION OF THE GRAPHIC ELEMENTS
The numbering below refers to the components of the device
shown on the graphic pages of this manual.
Designation
Description
1
Pressure bucket attachment
2
Pressure bucket arm
3
Pressure bucket
4
Rim protectors
5
Top ring
6
Supporting brackets for the top ring
7
Wheel mounting axle
8
Lever shaft with pin
9
Base of pressure bucket arm
10
Lower base ring
PURPOSE
The fitter is specifically designed for removing and fitting motorbike tyres
to rims.
ASSEMBLY
INSTRUCTIONS
The diagram shows the steps and the order of installation of the
components
Before assembling, check that all the necessary components for
assembly are available
•
Assemble the assembling unit by connecting the base ring (10) to the
top ring (5) using the support brackets (6). Screw these to the
connectors on both rings using bolts, washers and M6 nuts.
•
Then screw the base of the pressure bucket arm (9) with Allen screws
to the lower base ring (10)
•
Then mount the axle rod (7) to the base of the pressure bucket arm (9)
with two lock nuts
•
The next step is to mount the pressure bucket (3) with the pressure
bucket handle (1) and the pressure bucket arm (2) to the base of the
pressure bucket arm (9). The position of the pressure bucket (3) with
handle (1) is adjustable, allowing it to adapt its pressure bucket position
to the wheel size.
•
Then attach the pressure bucket arm (2) with the handle (1) and the
pressure bucket (3) to the base (9)
•
The last step is to assemble the protectors by snapping the 4 rim
protectors at a 90' angle to each other on the top ring.
KIT CONTENTS:
N
DESCRIPTION
QUANTITY
1
Lower base ring
1
2
Base of pressure bucket arm
1
3
Top ring
1
4
Pressure bucket arm
1
5
Pressure bucket arm attachment
1
6
Beadbreaker shovel
1
7
Wheel mounting axle
1
8
Supporting brackets for the top ring
4
9
Rim protectors
4
10
M14 axle-pin nuts
2
11
Allen screws m10
3
12
M8 X 60 screw
2
13
M8 lock nuts
2
14
M6 screw
16
15
M6 nut
16
16
M6 washer
16
Rated data
Maximum rim diameter
53cm
Minimum rim diameter
38cm
Dimensions
675 x 500 x 370 mm
Mass
7kg
10-602 indicates both the type and the designation of the device
ENVIRONMENTAL PROTECTION
The product should not be thrown away with household waste, but
should be disposed of at suitable facilities. A non-recycled product is a
potential danger to the environment and human health.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa with its
registered office in Warsaw, ul. Pograniczna 2/4 (hereinafter: "Grupa Topex") informs that
all copyrights to the content of this manual (hereinafter: "Manual"), including, among
others. Its text, photographs, diagrams, drawings, as well as its composition, belong
exclusively to Grupa Topex and are subject to legal protection under the Act of 4 February
1994 on Copyright and Related Rights (ie Journal of Laws 2006 No. 90 Poz. 631, as
amended). Copying, processing, publishing, modification for commercial purposes of the
entire Manual and its individual elements, without the consent of Grupa Topex expressed
in writing, is strictly prohibited and may result in civil and criminal liability.
EC Declaration of Conformity
Manufacturer: Grupa Topex Sp. z o.o. Sp.k., Pograniczna 2/4 02-285
Warszawa
Product: Mounting machine for motorbike wheels
Model: 10-606
Trade name: NEO TOOLS
Serial number
: 00001 ÷ 99999
This declaration of conformity is issued under the sole responsibility of
the manufacturer.
The product described above complies with the following documents:
Machinery Directive 2006/42/EC
And meets the requirements of the standards:
EN ISO 12100:2010; EN 1494:2000+A1:2008
This declaration relates only to the machinery as placed on the market
and does not include components
added by the end user or carried out by him/her subsequently.
Name and address of the EU resident person authorised to prepare the
technical dossier:
Signed on behalf of:
Summary of Contents for 10-606
Page 1: ...1...
