background image

Neo_M660A GPRS Module Hardware User Guide 

 

 

Copyright © Neoway Technology Co., Ltd 

20 

 

Figure 3-16

 

RING indicator for incoming call 

4 s

250 ms

250 ms

 

 

 

SMS: Upon receipt of SMS, the module outputs one 600 ms low pulse. 

Figure 3-17

 

RING indicator for SMS

 

600 ms

 

 

3.5 

SIM Card Interface

 

Table 3-5

 

SIM card interface 

Pin Name

 

I/O

 

Function Description

 

Remarks

 

VSIM 

SIM card power supply output 

1.8/3.0V 

SIM_CLK 

DO 

SIM card clock output 

 

SIM_RST 

DO 

SIM card reset output 

 

SIM_DATA 

DI/O 

SIM card data IO 

With internal pull-up resistor 

 

M660A supports 3.0 V and 1.8 V SIM cards. VSIM supplies power for SIM card at Max. 30 mA. 

SIM_DATA is pulled up by an internal resistor. You do not have to add and external pull-up resistor in your 
design. 

SIM_CLK can work at several frequencies at 3.25 MHz typically. SIM card is sensitive to GSM TDD noise 
and RF interference. So, the PCB design should meet the following requirements: 

 

The antenna especially build-in antenna should be installed a long distance away from the SIM card 
and SIM card traces. 

 

The PCB traces of SIM should be as short as possible and shielded with GND copper. 

Summary of Contents for Neo_M660A










































Reviews: