background image

 

SKG3 Gas Fired Humidifier 

Installation Instructions and User Manual

 

 

37 

Commissioning – Operation Description 

Control Panel 

Description 

The control panel of the Neptronic® SKG3 Steam humidifier is equipped with a user 
friendly LCD display and extensive access to status, alarms, and set-up menus. 

 

Control panel - Fig. 49 

Access to Menu 

To access the menu, press on the 

 button. The LCD will display the following list 

of menus: 

 

1.  Status 
2.  Control Set-up 
3.  System Set-up 
4.  Alarms 
5.  Diagnostics 

6. 

Com Set-up 

 

 

Use the 

 or 

 buttons to scroll up or down, and access a menu by pressing the 

 button. 

 

Within a menu, press on the 

 or 

 buttons to pass from one screen to another. 

 

The initial menu may be returned to at any time by pressing the 

 button. 

Changing Values 

Within the selected screen, press the 

 or 

 buttons until you have reached the 

desired value. 

Validate your selection by pressing on the 

 button. 

 

LCD

Display

Blue Power ON LED

ON/OFF Push button

Manual Drain Push button

Scroll DOWN

‘’

-

‘’ button, to decrease value

‘’

+

’’ button, to increase value

Scroll UP

ENTER button

Menu button

Red ALARM LED

All manuals and user guides at all-guides.com

Summary of Contents for SKG3 Series

























































Reviews: