background image

 

SKGE3 Gas Fired Humidifier 

Installation Instructions and User Manual

 

 

Safety 

WHAT TO DO 

IF YOU SMELL GAS! 

 

Do not try to light any appliance. 

Do not touch any electrical switch; do not use any telephone in your building. 

Immediately call your gas supplier from an off-site telephone. 

Follow the gas supplier's instructions.  

If you cannot reach your gas supplier, call the fire brigade. 

GAS 

 

Before installation, check that the local distribution conditions, nature of gas and pressure, and 
the current state adjustment of the appliance are compatible. 

Improper  installation,  adjustment,  alteration,  service,  maintenance  or  use  can  cause 
carbon monoxide poisoning, explosion, fire, electrical shock or other conditions which 
may cause personal injury or property damage. 

This appliance MUST be used only in sufficiently ventilated space. Consult instructions before 
installation and use of this appliance 

Installation and service MUST be performed by a qualified gas installer, service agency, or the 
gas supplier. 

Ensure that local regulations concerning the provision of gas installations are 
followed.

 

ELECTRICITY 

 

All work concerned with electrical installation MUST only be performed by skilled and qualified 
technical  personnel  (e.g.  electrician  or  technician  with  appropriate  training).  The  customer  is 
always responsible for ensuring the suitability of the technical personnel. 

Ensure  that  the  local  regulations  concerning  the  provision  of  electrical  installations 
are followed.

 

HEALTH & 

SAFETY 

Neptronic  has  considered  aspects of  the  design  of  their  humidification  systems  to  reduce  as 
much 

as  possible  the  risk  of  Legionnaires’  disease  and  other  similar  conditions,  but  it  is 

important that users are also aware of their responsibilities under  Health & Safety regulations 
in reducing the risk of legionellosis. 

To prevent the growth of Legionella, users are required to: 

 

Avoid water temperature that favours the growth of Legionella (20-45

˚C). 

 

Avoid water stagnation. 

 

Clean  and  disinfect  the  humidification  system  in  accordance  to  Health  &  Safety 
regulations and enclosed instructions. 

 

Carry  out  a  risk  assessment  of  the  water  system  supplying  the  humidifier  by  a 
competent person, to ensure the water supply is of an acceptable quality 

CORRECT USE 

Neptronic® systems and products are designed only for humidification use. 

Any other application is not considered as usage for the intended purpose. The manufacturer 
cannot be made liable for any damage resulting from incorrect use. 

ACCESS 

The  SKGE3  cabinet  keys  MUST  never  be  left  in  the  door  locks,  as  this  may  cause 
unauthorized  access  to  live  electrical  parts.  Always  store  keys  centrally  with  a  nominated 
responsible person. 

WATER 

Neptronic®  systems  are  designed  to  be  used  with  tap,  reverse  osmosis,  de  mineralized  or 
partially softened water. On no account attempt to introduce any other fluids or chemicals into 
the system without first consulting Neptronic or its authorized distributor. 

Water  supply  must  not  exceed  the  max  pressure  of  4.8  bar  or  pressure  limits  laid  out  in  the 
specification  and  installation  must  comply  with  local  regulations.  Your  attention  is  drawn  to 
your  responsibilities  as  outlined  in  the  Health  &  Safety  regulations.  The  control  of Legionella 
bacteria  in  water  systems  and  your  SKGE3  steam  humidifier  must  be  included  in  the  risk 
assessment of the water system in your building as a whole. In particular, if the humidifier is 
turned off for prolonged periods, you must ensure that the unit is drained and that stagnation 
is avoided in pipe work supplying it. 

A  competent  individual  or  organization  must  be  appointed  to  carry  out  water  tests.  A  wide 
range  of  different  tests  are  available  to  identify  the  presence  of  microbes  in  water,  including 
total  viable  count  (TVC),  temperature-range  specific  tests  and  identification  of  particular 
species  types  including  Legionella. 

It  is  the  responsibility  of  the  person  on  whom  the 

statutory  responsibility  falls  to  determine  the  type  and  frequency  of  this  and  all  other 
controls and preventative measures outlined in this manual.

 

WARRANTY 

Failure to install this humidifier as outlined in this manual may invalidate the warranty. 

!

!

All manuals and user guides at all-guides.com

Summary of Contents for SKGE3 Series

























































Reviews: